Portwest Hard Hats
8 hard hats from Portwest, listed with what Portwest publishes, and live prices.
Pick a ansi type, electrical class, brim or vents; the list below narrows as you choose. Prices are live.
8 products
Ratings and specifications are as published by each manufacturer. Tap a group to open it.
Portwest8 products
- Portwest PH55 Endurance Hard Hat Slip Ratchet — Portwest · ANSI type: Type I · Electrical class: Class C · Adjustment: Ratchet · Standards: ANSI/ISEA Z89.1 Type I Class C; EN 397 -10°C/+50°C
- Portwest PS52 Full Brim Future Hard Hat — Portwest · ANSI type: Type I · Electrical class: Class E · Brim: Full Brim · Standards: ANSI/ISEA Z89.1 Type I Class E; EN 397 -10°C/+50°C
- Portwest PS54 Endurance Plus Hard Hat — Portwest · ANSI type: Type I · Electrical class: Class E · Standards: ANSI/ISEA Z89.1 Type I Class E; EN 397 -30°C/+50°C, LD, 440VAC; EN 50365:2023 Type B Class 0
- Portwest PS56 Full Brim Premier Hard Hat — Portwest · ANSI type: Type I · Electrical class: Class E · Brim: Full Brim · Standards: ANSI/ISEA Z89.1 Type I Class E
- Portwest PV60 Peak View Ratchet Hard Hat Vented — Portwest · ANSI type: Type II · Electrical class: Class C · Adjustment: Ratchet · Vents: Vented · Standards: ANSI/ISEA Z89.1 Type II Class C; EN 397 -20°C
- Portwest PW02 Safety Pro Hard Hat Vented — Portwest · ANSI type: Type I · Electrical class: Class C · Vents: Vented · Standards: ANSI/ISEA Z89.1 Type I Class C
- Portwest PW52 Full Brim Premier Hard Hat Vented — Portwest · ANSI type: Type I · Electrical class: Class C · Brim: Full Brim · Vents: Vented · Standards: ANSI/ISEA Z89.1 Type I Class C
- Portwest PW67 Base Pro Hard Hat — Portwest · ANSI type: Type I · Electrical class: Class E · Standards: ANSI/ISEA Z89.1 Type I Class E
Do not see what you need? Browse the category or call (925) 215-7337.
In plain words. Hard hats are marked under ANSI/ISEA Z89.1. Type I protects against a blow to the top of the head; Type II also protects against blows from the side, front and back. The electrical class is separate: Class G (general) is tested to 2,200 volts, Class E (electrical) to 20,000 volts, Class C (conductive) is not tested for electrical protection and may be vented. Bump caps are not hard hats; they protect against bumps and scrapes only. The manufacturer prints the Type and Class inside the shell.
Technical. ANSI/ISEA Z89.1-2014 (R2019): Type I impact and penetration from above; Type II adds lateral impact (EN 12492 climbing-style helmets are tested similarly and are sold here where the manufacturer rates them to Z89.1 Type II); Class G 2,200 V, Class E 20,000 V, Class C no electrical rating; optional marks LT (low temperature, −30 °C), HV (high visibility), and the reverse-donning arrow. CSA Z94.1 is the Canadian equivalent. Suspension points, ratchet or pin-lock adjustment, brim style and vents are as published.
Ratings and specifications on this page are shown as published by the manufacturer or the named standard and describe performance in that standard's test. They are not a recommendation for any task. The employer's hazard assessment decides what protective equipment a job needs. Verify details against the manufacturer's current documentation before you buy.
The standard at a glance
Copied from the named standard or regulation and shown with its source; nothing in these tables is Bayshore's recommendation.
ANSI/ISEA Z89.1 types and classes
| Mark | What it means in the standard |
|---|---|
| Type I | Impact and penetration protection from a blow to the top of the head |
| Type II | Type I plus lateral impact (front, back and sides) |
| Class G (General) | Tested at 2,200 volts |
| Class E (Electrical) | Tested at 20,000 volts |
| Class C (Conductive) | No electrical protection; may be vented |
| LT | Low-temperature tested (−30 °C) |
| HV | High-visibility shell |
| Reverse-donning arrow | Tested worn backwards |
Source: ANSI/ISEA Z89.1-2014 (R2019), American National Standard for Industrial Head Protection. Bump caps are not covered by Z89.1.