Skip to main content
Home › Guides › Hand protection › Leather gloves in wet and cold
Guide · Hand protection · OSHA 3151 · EN 511 · MCR Safety welding and winter guides

Bayshore Safety & Industrial Supplies Guide

Will leather gloves shrink if they get wet, and do leather gloves keep you warm in winter? What heat does to leather, what the lining does, and what MCR Safety states

Water does not shrink leather; heat does. A leather work glove soaked on the job and dried slowly at room temperature, reshaped on the hand as it dries and conditioned when nearly dry, comes back close to its size. The same glove dried on a heater, in a hot truck cab, in the sun or in a dryer shrinks, stiffens and cracks, because the heat drives out the oils that keep the hide flexible; MCR Safety’s welding guide states the same mechanism for open flame, which burns the natural oils and tanning chemicals out of leather so the glove hardens and chars. Warmth is a separate question with a plain answer: leather is the shell, and a leather glove is only as warm as the lining inside it. OSHA’s PPE booklet lists leather for sparks, moderate heat, blows, chips and rough objects, not for cold, and an unlined drivers glove carries no cold rating. MCR Safety lines its winter leather gloves with fleece, pile, foam, wool, Thermosock or Thinsulate, ranks those linings in that order from “good” to “great” in its winter glove guide, and states the EN 511 contact cold level where it has tested one (level 2 on a Thermosock-lined pigskin drivers glove). Wet leather conducts heat away faster than dry, so a glove that got soaked is the one that gets cold.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · OSHA Publication 3151-12R 2004, Personal Protective Equipment, hand and arm protection section (osha.gov, read Nov 9 2026); MCR Safety, “Welding Guide”, page 2 (leather material breakdown; what flame does to leather); MCR Safety, “Winter Glove Guide” (lining comparison: fleece, foam, acrylic, wool, Thermosock, Thinsulate); EN 511 (contact cold level, as MCR Safety states it); manufacturer care instructions as summarized in the leather care guide (PIP, MCR Safety, Caiman, Black Stallion, Tillman); MCR Safety product pages and specification sheets for the styles shown; Liberty Safety product pages and spec sheets (libertysafety.com, read Nov 11 2026)
MCR Safety 32013T Drivers Gloves, Cowhide, Competitive Value C+ GradeMCR Safety 32013T Drivers Gloves, Cowhide, Competitive Value C+ GradeInsulated drivers glove with the lining and grade MCR Safety states (MCR Safety data)

Why wet and cold are two different questions. Leather is a tanned hide: the tanning fixes the collagen and leaves oils in the fibers that keep them sliding over one another, which is the flexibility a glove needs. Water fills the fibers and then evaporates; if it evaporates slowly, the oils stay and the glove relaxes back to shape. If it is driven out fast by heat, the fibers shrink and lock, the oils go with the water, and the hide comes out smaller, harder and prone to cracking at the flex points, which is why every manufacturer’s care instruction on the leather care guide says cool water, no machine, no dryer, no heater. Cold works on a different part of the glove. The hide itself holds little air, so an unlined leather glove is wind-resistant but not insulating; what keeps the hand warm is the loft of the lining, and what defeats it is water, which collapses the loft and conducts the heat out. That is why MCR Safety pairs its winter leather gloves with a lining it names and, on the wet-work styles, a waterproof bladder, and why the EN 511 rating a winter glove carries belongs to the whole glove, not the leather.

The linings MCR Safety puts inside leather, in its own order

From MCR Safety’s winter glove guide, least to most warm; the lining on each product page.

Fleece (good)Brushed cotton or cotton blend, the common lining on drivers and leather palm winter gloves and on fleece-lined welding gloves.
Foam (good)A foam layer under the palm leather; also used in welding gloves for heat.
Pile and thermal knits (better)A deep knit lining that captures body heat, as acrylic does in MCR Safety’s coated winter gloves.
Wool (better)The natural insulator that still insulates damp; MCR Safety lines one pigskin leather palm glove with it.
Thermosock (great)MCR Safety’s own high-loft synthetic fiber, chosen for weight-to-warmth; in its Artic Jack and Luminator pigskin drivers and leather palm gloves.
Thinsulate (great)3M’s synthetic microfiber in 40, 100 and 200 gram weights, for warmth-to-thickness; MCR Safety lines a cowhide drivers glove and a deerskin drivers glove with C100.

What to do with a wet leather glove, and how to read a winter leather glove page

  • Soaked on the job: press the water out in a towel (do not wring), put the glove on for a minute to reshape it, dry it flat or hanging at room temperature away from heat and sun, and work in a little conditioner when it is nearly dry. The leather care guide has the full steps.
  • Never: a dryer, a heater, a dashboard, a hot truck cab, hot water, bleach, detergent or solvent; the stiffness and shrinkage they cause are mostly permanent.
  • Welding gloves: condition sparingly or not at all, because oil in the leather lowers its heat resistance; a welding glove that has hardened from flame is replaced, not softened.
  • Lining: the product page names it (fleece, foam, pile, thermal, wool, Thermosock, Thinsulate C100) and MCR Safety lists “Insulated” in the features; unlined gloves say so.
  • EN 511: where MCR Safety has tested the glove, the contact cold level is stated (level 2 on the Luminator 34411 pigskin drivers glove); MCR Safety does not publish the convective cold or water digits. No EN 511 figure means no cold rating, whatever the lining.
  • Hide and grade: pigskin, with the porous grain the manufacturers list as drying soft, is the hide MCR Safety uses on most of its Artic Jack winter gloves; deerskin is the softest; the grade (Premium A, Select B, Competitive Value C) is MCR Safety’s sort of the hide and is on every page.
  • Size: a lined glove is often bought a size up, and MCR Safety’s leather gloves are lettered only, from its palm-width chart (the size guide).
MCR Safety, “Winter Glove Guide”; MCR Safety, “Welding Guide”, page 2; EN 511 as stated on the MCR Safety product pages; MCR Safety product pages and specification sheets for the styles shown

Questions people ask

Will leather gloves shrink if they get wet?

Not from the water. Dried slowly at room temperature and reshaped on the hand they come back close to size; dried with heat (a heater, a dryer, the sun, a hot cab) they shrink, stiffen and crack because the heat drives the oils out of the hide.

Do leather gloves keep you warm in winter?

Only as warm as the lining. Leather is the shell; MCR Safety ranks its linings fleece, foam, acrylic, wool, Thermosock and Thinsulate and states the EN 511 contact cold level where it has tested the glove. An unlined leather glove has no cold rating.

What is the warmest lining for leather gloves?

By MCR Safety’s ranking, Thinsulate and Thermosock (“great”), then wool (“better”), then foam and fleece (“good”); its Thinsulate C100 cowhide and deerskin drivers gloves and its Thermosock pigskin gloves are the top of its winter leather line.

Are leather gloves waterproof?

No. Leather absorbs water, and wet leather conducts heat away faster than dry. MCR Safety lists a waterproof bladder on some insulated styles; the leather itself is not the barrier.

How do you dry leather gloves that got wet?

Press, don’t wring; reshape on the hand; dry flat or hanging at room temperature away from heat and sun; condition lightly when nearly dry. The leather care guide gives the steps and what never to use.

Is pigskin or cowhide better in the wet?

MCR Safety uses pigskin on most of its Artic Jack winter gloves, a porous hide the manufacturers list as drying soft; cowhide is thicker and more abrasion resistant. Both lose warmth when soaked, and both are dried the same slow way.

Why are leather gloves so expensive?

The hide and the grade set the price: Premium A and A+ hides cost more than Select B and Competitive Value C, goatskin and deerskin more than cowhide and pigskin, and a lining adds to it. The grade is on each MCR Safety page and the price on each row is the one listed today.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Need gloves matched to a crew’s work?Call (925) 215-7337 or email us the task, the hazard and the sizes and we will quote by the dozen with the manufacturer’s ratings listed.
Work glove selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.