Skip to main content
Home › Guides › Hand protection › How work gloves should fit
Guide · Hand protection · Fit and sizing

Bayshore Safety & Industrial Supplies Guide

How snug should work gloves be? The signs a glove is too large or too tight from the Armor Guys FAQ, sizing up or down, finding your size without a tape, how big a 3X glove is, the Armor Guys size chart in inches, and winter gloves

A work glove should be snug enough that the fingertips reach the end of the glove fingers and the palm has no spare material to bunch, and loose enough that the hand closes without the knuckles pulling the coating tight; Armor Guys’ product pages put it in one sentence, "the best fit preserves fingertip control without excess palm material or cuff movement". Its FAQ gives the signs on each side: too large is "fingertip bunching, poor tool control, slipping, and workers removing gloves for detailed work"; too tight is "pressure points, hand fatigue, reduced range of motion, and discomfort during long shifts". The size is a measurement, not a guess: Armor Guys’ workbook says to measure the circumference of the dominant hand just below the knuckles, in inches, and that number is the size, XS at 6 inches through S 7, M 8, L 9, XL 10, XXL 11 and XXXL 12. A 3X glove is therefore a 12-inch hand, and 3X is the largest size on the Armor Guys styles we list, printed on 16 of them.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · Armor Guys Product Knowledge Workbook C.010, page 12, "How to determine your glove size" (armorguys.com/downloads/resources/C.010-V1-Product-Knowledge-Workbook-PQ.pdf, read Nov 12 2026); Armor Guys Industrial Glove Sizing Chart and FAQ pages (armorguys.com/resources/glove-sizing-chart and /faqs, read Nov 12 2026); Armor Guys product pages and spec sheets for the styles shown (armorguys.com, read Nov 12 2026); 29 CFR 1910.132 Personal protective equipment, general requirements (eCFR, saved Nov 12 2026)
Armor Guys 00-840 Kyorene Pro Cut Resistant Gloves, ANSI A4, Foam Nitrile PalmArmor Guys 00-840 Kyorene Pro Cut Resistant Gloves, ANSI A4, Foam Nitrile PalmArmor Guys lists the Kyorene Pro 00-840 in XS to 3X, a 6-inch to a 12-inch hand by its chart, an 18-gauge A4 glove with a touchscreen fingertip, $131.26 a dozen

Why fit is a safety figure. Armor Guys’ sizing page opens with it: "Sizing affects safety because loose gloves reduce control and tight gloves increase fatigue", and "Fit controls dexterity, comfort, grip, and worker compliance. A glove that is too large can bunch at the fingertips, while a glove that is too tight can create fatigue during repetitive work." A glove that comes off for the fiddly part of the job protects nothing, and a cut-rated glove’s level is tested on the palm material under tension, not on a bunched one. OSHA’s PPE rule makes fit the employer’s job too: 29 CFR 1910.132(d) requires the hazard assessment to select PPE "that properly fits each affected employee", and 1910.132(f) requires training in how to put it on and adjust it.

How to measure, and what the number means. Wrap a tape around the dominant hand just below the knuckles, thumb out, and read inches. Armor Guys’ chart: 6 inches is XS, 7 is S, 8 is M, 9 is L, 10 is XL, 11 is XXL (2X), 12 is XXXL (3X). The numbers are also the European and numeric glove sizes, which is why a size 10 glove is an XL and a size 9 is a large, as the numeric-size guide linked below explains. Armor Guys color-codes the cuff overlock by size on its knits so a crew can tell sizes apart in a bin, and prints the same price for every size, so there is no reason to buy the wrong one.

The questions in short

From the Armor Guys FAQ, sizing chart and workbook; the long answers follow.

How snug should work gloves be?Fingertips to the end, no spare palm material, hand closes freely: "fingertip control without excess palm material or cuff movement" in Armor Guys’ words.
Size up or down?Neither; measure. Between sizes, down for a coated knit that stretches and for fine work, up for a liner underneath, a winter lining or a thick leather palm.
How big is a 3X glove?A 12-inch hand circumference below the knuckles, by the Armor Guys chart; XXL is 11 inches.
What is the biggest glove size?XXXL (3X) on the Armor Guys chart, at 12 inches, printed on 16 of the styles here; some other manufacturers list 4XL and 5XL, shown in the band.
How do I find my size without a tape?A string and a ruler around the hand below the knuckles; or the width of the palm across the knuckles, about 3.5 inches is M, 4 is L, 4.5 is XL, as a rough cross-check.
Is there a size chart?Yes, the Armor Guys chart in the next section: XS 6 in, S 7, M 8, L 9, XL 10, 2X 11, 3X 12.
Signs a glove is too large?"Fingertip bunching, poor tool control, slipping, and workers removing gloves for detailed work", per the Armor Guys FAQ.
Signs a glove is too tight?"Pressure points, hand fatigue, reduced range of motion, and discomfort during long shifts", per the same FAQ.
The Armor Guys glove size chart (hand circumference below the knuckles)
SizeHand measurementAlso written as
XS6 inches6
S7 inches7
M8 inches8
L9 inches9
XL10 inches10
XXL (2X)11 inches11
XXXL (3X)12 inches12

Measure the circumference of the dominant hand just below the knuckles, thumb excluded. Armor Guys identifies the size by the cuff color on its knit styles and prices every size the same.

Source: Armor Guys Product Knowledge Workbook C.010, page 12, "How to determine your glove size" (armorguys.com/downloads/resources/C.010-V1-Product-Knowledge-Workbook-PQ.pdf, read Nov 12 2026)

The questions, one by one

Each answer draws on the Armor Guys FAQ, sizing page and workbook, the product pages and the OSHA text named in the byline.

How snug should work gloves be, and how do I tell?

Put the glove on and make a fist, then pick up a small part. If the fingertips of the glove fold over or the palm wrinkles when you grip, it is too large; Armor Guys’ FAQ lists "fingertip bunching, poor tool control, slipping" as the signs, and the tell-tale on a crew is "workers removing gloves for detailed work". If the knuckles blanch the coating, the cuff cuts in, or the hand aches by the break, it is too tight; the FAQ lists "pressure points, hand fatigue, reduced range of motion". The right size is the one where a coated knit follows the hand like a second skin without pulling: a 13- to 18-gauge knit stretches, which is why it can be snug, and a 7- or 10-gauge knit or a leather palm does not, which is why those run a touch looser.

Is it better to size up or down for gloves?

Measure first; the chart is a measurement, not a preference. When the number falls between sizes, go down for a thin coated knit that will be worn for fine work and will stretch into shape, and go up for a glove that will go over a liner, a winter glove whose lining takes space (Armor Guys lists its 7-gauge-lined winter styles from S or M for that reason), a leather palm that does not stretch, or a hand that is wide across the knuckles for its circumference. Armor Guys’ sizing page says to validate with a trial: "Give each work group a small range of sizes and capture feedback after real use", and its FAQ adds that standardizing on one style "does not mean standardizing one size".

How big is a 3X glove, and what is the biggest size?

On the Armor Guys chart XXXL, which the product pages write 3X, is a 12-inch hand circumference below the knuckles, one inch above XXL. It is the largest size Armor Guys makes on the styles we list, and it is printed on 16 of the 110: among them the Basetek 02-013, 02-014, 02-023 and 02-025, the Kyorene 00-200, 00-300, 00-420 and 00-600, the Kyorene Pro 00-840, 00-857 and 00-897, and the Extraflex winter 04-311, 04-312, 04-314, 04-321 and 04-545. A few other manufacturers list 4XL and 5XL on specific styles, which the comparison group in the band shows as printed. At the other end Armor Guys prints XXS on the Basetek 02-013 and 02-015, and XS, a 6-inch hand, on most of the line.

How do I know my hand size for gloves without a measuring tape?

Wrap a piece of string, a shoelace or a strip of paper around the dominant hand just below the knuckles, thumb out, mark where it meets, and lay it against a ruler or a tape measure on a tool; the inches are the size on the chart above. If there is no ruler either, a dollar bill is 6.14 inches long: a hand that a bill just wraps is an XS, a hand that needs a bill and a half is a L. A cross-check from the palm: the width across the four knuckles runs about 3.5 inches for a medium, 4 for a large and 4.5 for an XL, which is rough and is no substitute for the circumference.

Can you provide a chart of glove sizes, including numeric sizes?

The chart above is Armor Guys’ own, in inches, and the inch figure is the numeric size: 7 is S, 8 is M, 9 is L, 10 is XL, 11 is 2X, 12 is 3X. Manufacturers that print numeric sizes, as several in the band do on leather and cut-resistant knits, mean the same measurement; the numeric-size guide and the measuring guide linked below carry those brands’ charts beside this one, and the women’s-size guide covers the small end of the scale.

Should a liner change the size, and how are winter gloves sized?

A liner worn under a glove takes room, so the outer glove is sized over it; the glove-liners guide linked below covers the pairings. Armor Guys’ winter styles have the lining built in, a 7-gauge poly-acrylic knit under the shell, and are sized as a unit, which is why Armor Guys lists them from S or M rather than XS; measure as usual and take the chart size, and size up only if the hand is between sizes, because a winter glove that squeezes the lining flat loses the trapped air that keeps the hand warm. The cold-materials guide linked below has the EN 511 figures.

Does OSHA say anything about glove fit?

Yes. 29 CFR 1910.132(d)(1)(iii) requires the employer to "select PPE that properly fits each affected employee", and 1910.132(f)(1) requires training in "how to properly don, doff, adjust, and wear PPE". 1910.138(b) bases glove selection on the task, conditions and duration of use. Fit is therefore part of the hazard assessment, and a crew with a range of hand sizes needs a range of glove sizes stocked, which is the point Armor Guys’ FAQ makes for procurement.

In plain words

  • Snug means fingertips to the end, no spare palm, hand closes freely. Bunching means too big; pressure points and fatigue mean too tight.
  • Measure around the dominant hand below the knuckles: 6 in XS, 7 S, 8 M, 9 L, 10 XL, 11 2X, 12 3X, by the Armor Guys chart.
  • A 3X glove is a 12-inch hand; 3X is the largest Armor Guys size here, printed on 16 styles.
  • Between sizes: down for a thin coated knit, up over a liner, a lining or leather.
  • OSHA 1910.132(d) requires PPE that properly fits each employee; Armor Guys prices every size the same.
Armor Guys Product Knowledge Workbook C.010, page 12, "How to determine your glove size" (armorguys.com/downloads/resources/C.010-V1-Product-Knowledge-Workbook-PQ.pdf, read Nov 12 2026); Armor Guys Industrial Glove Sizing Chart and FAQ pages (armorguys.com/resources/glove-sizing-chart and /faqs, read Nov 12 2026)

Questions people ask

How snug should work gloves be?

Fingertips reach the end, no spare palm material, the hand closes freely; Armor Guys’ FAQ lists bunching and slipping as too large, pressure points and fatigue as too tight.

How do I measure my glove size?

Circumference of the dominant hand just below the knuckles, thumb out, in inches: 6 XS, 7 S, 8 M, 9 L, 10 XL, 11 2X, 12 3X, per the Armor Guys workbook.

How big is a 3X glove?

A 12-inch hand circumference on the Armor Guys chart, one inch above 2X.

What is the biggest work glove size?

3X (12 inches) on the Armor Guys styles here, printed on 16 of them; a few other manufacturers list 4XL and 5XL on specific styles.

Should I size up or down?

Measure first; between sizes, down for a thin stretchy knit, up over a liner, a winter lining or a leather palm.

How do I size gloves without a tape?

A string or paper strip around the hand below the knuckles, measured against a ruler; a dollar bill is 6.14 inches as a rough gauge.

Do winter gloves run small?

Armor Guys sizes its lined winter styles as a unit and lists most from S or M; take the chart size and do not squeeze the lining.

Does OSHA require gloves to fit?

Yes; 29 CFR 1910.132(d)(1)(iii) requires PPE that properly fits each affected employee.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Need gloves matched to a crew’s work?Call (925) 215-7337 or email us the task, the hazard and the sizes and we will quote by the dozen or the case with the manufacturer’s ratings listed. We sell nationwide.
Work glove selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.