Skip to main content
Home › Guides › Heat, cold and ergonomics › Gloves for cold materials
Guide · Heat, cold and ergonomics · Cold

Bayshore Safety & Industrial Supplies Guide

Which gloves for handling extremely cold materials? Contact cold under EN 511, the Armor Guys winter styles and their X2X and X21 codes, what temperature calls for gloves, why fingers still get cold, touchscreen winter gloves and liners

For handling cold materials, cold parts, frozen product, wet steel in winter, the figure to read is the EN 511 contact cold level, the middle digit of the three-digit code, scored 0 to 4 for the thermal resistance of the glove material against a cold object, as Armor Guys prints the table in its catalog. The first digit is convective cold, the insulation of the whole glove against cold air, and the third is water penetration, 0 or 1. Armor Guys prints EN 511 X2X on its Extraflex winter styles (contact cold 2, convective and water not tested) and X21 on the waterproof Kyorene Pro 00-849WP and 00-869WP (contact cold 2, no water penetration), all on a 7-gauge poly-acrylic lining under a cut-rated shell. OSHA’s hand protection rule, 29 CFR 1910.138, lists "harmful temperature extremes" among the hazards an employer must select gloves for, and sets no temperature; the band below lists the winter gloves by the figure their manufacturer prints.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · Armor Guys Product Catalog C.009, page 4, "Cold Protection EN511" (armorguys.com/downloads/resources/C.009-Web.pdf, read Nov 12 2026); Armor Guys product pages and spec sheets for the styles shown (armorguys.com, read Nov 12 2026); 29 CFR 1910.138 Hand protection (eCFR, saved Nov 12 2026); Cal/OSHA Title 8 sections 3380, 3383 and 3384 (dir.ca.gov, saved Nov 12 2026); the other brands’ EN 511 codes as their manufacturers print them
Armor Guys 00-849WP Kyorene Pro Winter Work Gloves, ANSI A4, Foam Nitrile PalmArmor Guys 00-849WP Kyorene Pro Winter Work Gloves, ANSI A4, Foam Nitrile PalmArmor Guys prints EN 511 X21 on the Kyorene Pro 00-849WP: a waterproof A4 winter glove with a 7-gauge poly-acrylic lining, micro-foam nitrile grip and a touchscreen fingertip, $203.45 a dozen

Three digits, three tests. EN 511 is the European standard for gloves against cold, and Armor Guys lays its table out on the catalog page beside EN 388 and EN 407: resistance to convective cold, performance level 0 to 4, "based on the thermal insulation properties of the glove which are obtained by measuring the transfer of cold via convection"; resistance to contact cold, 0 to 4, "based on the thermal resistance of the glove material when exposed to contact with a cold object"; and penetration by water, 0 or 1, where 1 means no water penetration. The catalog adds that all gloves must achieve at least performance level 1 for abrasion and tear under EN 388. An X in a position means that test was not run. So a glove marked X2X was tested for contact cold and scored level 2, and was not tested for convective cold or water; a glove marked X21 scored contact cold 2 and kept water out.

Which digit for which cold. Handling cold materials is contact cold: a frozen case, a steel beam at dawn, a cylinder, a cold casting, a wet net. The middle digit is the one. Standing in cold air for a shift is convective cold, the first digit, and there the lining thickness and a windproof back matter more than the palm. Wet cold is the third digit plus a coating or membrane that keeps the lining dry, because a wet lining stops insulating. The Armor Guys winter styles put a 7-gauge poly-acrylic lining under a 13- or 18-gauge cut-rated shell with a micro-foam nitrile or latex palm, and the WP versions add a waterproof membrane; that is why the same contact cold 2 appears with X2X on the Extraflex and X21 on the Kyorene Pro WP.

The questions in short

From the EN 511 table Armor Guys prints and the product pages; the long answers follow.

Which gloves for extremely cold materials?Gloves with a stated EN 511 contact cold level, the middle digit, and a lining that stays dry: Armor Guys prints contact cold 2 on every winter style it makes, with a waterproof membrane on the WP styles.
What temperature is cold enough for gloves?No rule names one. OSHA 1910.138 and Cal/OSHA 3384 list harmful temperature extremes as a hazard to select gloves for; the practical line is when fingers lose feeling or grip, which depends on wind and wet as much as the reading.
Why do fingers still get cold in gloves?A wet lining, a glove too tight to trap air, a thin palm against a cold object (contact cold), or a glove rated for air and not for contact. The figures tell which.
Touchscreen gloves for cold weather?The Armor Guys Kyorene Pro winter styles (00-849, 00-849WP, 00-869, 00-869WP) print a touchscreen fingertip beside the EN 511 code; the band lists them.
Freezer gloves with grip?A micro-foam nitrile or latex palm over the lining: Armor Guys lists its winter styles for cold storage and prints the grip coating on each.
Do glove liners keep hands warmer?A thermal liner adds a dead-air layer under a shell; a cut-resistant liner adds cut protection, not warmth, and Armor Guys states no cold figure on its liners.
Are silk gloves warm?A silk liner is a thin layer that adds a little air and wicks; it carries no EN 511 figure and is not a work glove. We do not sell silk liners.
What are the warmest gloves?The ones with the highest stated EN 511 digits for the cold in question, kept dry; "warmest" is not a figure, the digits are.

The questions, one by one

Each answer is drawn from the Armor Guys catalog and product pages, the OSHA and Cal/OSHA texts, and the manufacturers’ EN 511 codes named in the byline.

Which type of gloves is used for handling extremely cold materials?

A lined, coated glove with a stated contact cold level. On the Armor Guys winter styles the lining is a 7-gauge poly-acrylic knit, the shell is a 13-gauge Extraflex or an 18-gauge Kyorene Pro cut-rated knit, the palm is micro-foam nitrile or latex, and the printed code is EN 511 X2X or X21, contact cold level 2 either way. For handling frozen product or cold wet parts the WP styles add a waterproof membrane and print the water digit as 1. For very cold materials, cryogenic liquids, dry ice, liquid nitrogen, a cold-storage glove is not the answer at all; those call for cryogenic gloves tested for that use, which is a different product we do not list here.

What temperature is cold enough to wear gloves?

There is no temperature in the rules. 29 CFR 1910.138(a) requires employers to select hand protection when hands are exposed to hazards including "harmful temperature extremes", and 1910.138(b) bases the selection on the task, conditions, duration and hazards identified; Cal/OSHA 3384 says the same for California. The working answer is the one the crew gives: when fingers go numb, grip slips or a worker keeps pulling a hand into a sleeve, the glove on hand is not enough for that day. Wind and wet move that point a long way; a damp 40 °F morning on steel takes more glove than a dry 25 °F one. The cold stress guide linked below carries the NIOSH guidance on work in the cold.

Why do my fingers still get cold in gloves?

Four reasons the figures explain. The lining is wet: sweat or water in a poly-acrylic lining stops it insulating, which is what the water digit and a membrane are for. The glove is too tight: insulation is trapped air, and a glove a size small squeezes it out, so a winter glove is sized to the lining, not to the summer glove. The hazard is contact and the glove was rated for air: a thin palm on a cold object conducts heat out faster than any back-of-hand insulation can replace it. Or the glove has no cold rating at all and was never tested; a sandy nitrile summer glove on a winter site is the usual case.

What are good touchscreen gloves for cold weather?

Armor Guys prints "touchscreen compatible" on its Kyorene Pro winter styles, 00-849 and 00-869 with a micro-foam nitrile palm and 00-849WP and 00-869WP with the waterproof membrane, rated A4 and A6 for cut and EN 511 X21 on the WP styles. The touchscreen fingertip is part of the knit, so it works through the glove without pulling it off, which is the point in the cold.

What are good freezer gloves with grip?

Cold storage is on the application list Armor Guys prints for every winter style, and each prints its palm: micro-foam nitrile on the Extraflex 04-311, 04-321, 04-322 and 04-545 and the Kyorene Pro winter styles, latex on the Extraflex 04-011 and 04-012. A freezer is dry cold with wet boxes, so the water digit matters less than the lining and the palm; a wet-work freezer, a fish house, is the WP case.

Do glove liners keep your hands warmer, and should you wear them?

A thermal liner, a thin knit worn under a shell glove, adds a layer of trapped air and can be changed when it gets damp, which is the reason to wear one on a long cold shift. The glove-liners guide linked below covers them. Armor Guys’ liners are a different thing: uncoated cut-resistant knits, the Taeki5 01-017, the Basetek 02-027 and the Kyorene Pro food-safe liners, worn under a glove for cut protection, with no cold figure stated. A liner under a glove that was sized without one makes the glove tight, and a tight glove is a cold glove.

Are silk gloves warm, and are wool gloves warm?

Silk liners are thin and wick moisture, and they add a little air under a shell, which is why they turn up under ski gloves; they carry no EN 511 figure and tear on a job site. Wool holds warmth when damp better than cotton does, which is why old wool liners are still around, but a wool liner has no cut rating and no grip. We sell neither as a work glove; a thermal liner and a rated winter glove do the same job with figures printed on them.

Which are the warmest gloves available?

The question has no single answer because the standard scores two kinds of cold. For air, the convective digit; for cold objects, the contact digit; for wet, the water digit. The Armor Guys winter styles print contact cold 2 and the WP styles water 1; the other manufacturers in the comparison band print their own codes, some with a convective digit, and the band shows each as printed so the gloves can be compared on the same table.

What type of gloves should be worn to protect hands from cold temperatures under OSHA?

OSHA names no glove type. 1910.138 requires selection based on the performance characteristics of the glove relative to the task, conditions, duration and hazards, so the employer’s hazard assessment (1910.132(d)) names the cold, the wet and any cut or impact hazard, and the glove picked has a figure for each. A cut-rated winter glove like the Armor Guys styles covers the cold and the cut in one; a job that also has a crush hazard adds the ANSI/ISEA 138 figure, which the Extraflex 04-312 and 04-314 winter impact styles print.

In plain words

  • EN 511 is three digits: convective cold 0 to 4, contact cold 0 to 4, water 0 or 1. X means not tested.
  • Handling cold materials is contact cold, the middle digit. Standing in cold air is the first digit. Wet work is the third plus a membrane.
  • Armor Guys prints X2X on its Extraflex winter gloves and X21 on the waterproof Kyorene Pro winter gloves, all with a 7-gauge poly-acrylic lining under a cut-rated shell.
  • No rule sets a temperature; OSHA 1910.138 and Cal/OSHA 3384 make harmful temperature extremes a hazard the employer selects gloves for.
  • Cold fingers in a glove usually mean a wet lining, a tight glove, or a glove rated for air and not for contact.
  • A thermal liner adds warmth; a cut-resistant liner adds cut protection. Silk and wool liners carry no figure and are not work gloves.
Armor Guys Product Catalog C.009, page 4, "Cold Protection EN511" (armorguys.com/downloads/resources/C.009-Web.pdf, read Nov 12 2026)

Questions people ask

Which gloves for extremely cold materials?

Lined gloves with a stated EN 511 contact cold level (the middle digit); Armor Guys prints contact cold 2 on all its winter styles and a waterproof membrane on the WP ones.

What does EN 511 X2X mean?

Convective cold not tested, contact cold level 2, water penetration not tested, per the table Armor Guys prints in its catalog.

What does EN 511 X21 mean?

Contact cold level 2 and water penetration 1, meaning no water got through; Armor Guys prints it on the 00-849WP and 00-869WP.

What temperature is cold enough to wear gloves?

No rule names one; OSHA 1910.138 makes harmful temperature extremes a hazard to select gloves for, and the sign is numb fingers or lost grip.

Why are my fingers cold inside gloves?

A wet lining, a glove too tight to hold air, a thin palm on a cold object, or a glove with no cold rating at all.

Are there touchscreen winter gloves?

Yes; Armor Guys prints a touchscreen fingertip on its Kyorene Pro winter styles 00-849, 00-849WP, 00-869 and 00-869WP.

Do liners make gloves warmer?

A thermal liner adds a layer of air; a cut-resistant liner such as the Armor Guys 01-017 adds cut protection and states no cold figure.

Are silk gloves warm?

A silk liner wicks and adds a little air under a shell but carries no EN 511 figure; it is not a work glove and we do not sell one.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Outfitting a crew for cold storage or winter work?Call (925) 215-7337 or email us the work and the temperature and we will quote insulated and liner gloves by the dozen with the manufacturer’s EN 511 and cut figures listed. We sell nationwide.
Work glove selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.