Bayshore Safety & Industrial Supplies Guide
Who wears orange hi-vis, and what do the vest colors mean? Orange-red vs yellow-green under ANSI/ISEA 107 and the MUTCD, who wears blue and yellow, pink, red, white, green and black vests, pink hi-vis and OSHA, shirt colors and hex codes
Orange hi-vis is worn by whoever the employer puts in it. The standard does not assign colors to trades: ANSI/ISEA 107 names three fluorescent background colors, yellow-green, orange-red and red, all equal in class, and the MUTCD 11th Edition section 6C.05 narrows the roadway to "fluorescent orange-red, fluorescent yellow-green, or a combination of the two". Within that, highway departments, utilities and railroads often specify orange for crews working against green roadside vegetation and yellow-green equipment, and general contractors often specify yellow-green (lime), which is the brighter of the two to the eye; a few sites use the two colors to tell crews apart. Every other color people ask about, blue, pink, red (other than fluorescent red), white, green, purple, gray and black, has no class: ML Kishigo makes vests in all of them in its Enhanced Visibility Series and labels them Non-ANSI, for visitors, events and sites with no vehicle hazard. The guide below goes through each color, what it means on the sites that use a color scheme, and why "pink OSHA approved" and "the hex code for safety yellow" have no answer in the standard.
ML Kishigo 1511 Safety Vest, Class 2 Type R, Orange, 6 Pockets, Zipper FrontML Kishigo labels it ANSI/ISEA 107 Type R Class 2 in fluorescent orange; Premium Brilliant SeriesWhat the standard says about color. ML Kishigo’s FAQ: fluorescent fabrics "use special pigments to appear brighter than other colors, and enhance daytime visibility, especially in low light such as cloud cover, dusk, dawn", and the standard "specifies minimum performance characteristics for fluorescent yellow-green, orange-red and red background materials". Those three are the hi-vis colors; a garment in any other background color cannot be labeled to a class however much tape it carries. On the roadway the MUTCD 6C.05 allows two of the three (orange-red and yellow-green) or a combination, and lets the retroreflective tape be "orange, yellow, white, silver, yellow-green, or a fluorescent version of these colors". Neither document says who wears which; "a person designated by the employer to be responsible for worker safety shall make the selection of the appropriate class of garment", and the color goes with it.
The colors, one by one
What each color is under the standard, and the conventions people ask about; the conventions are site or company practice, not a rule.
The questions, one by one
Answers from the ML Kishigo pages, the MUTCD and the regulations named in the byline.
Who wears orange hi-vis?
Road crews, more than anyone: state DOTs, highway contractors, utilities, railroads and tow operators often specify fluorescent orange-red because it reads against green roadside vegetation and against the yellow-green of the equipment, and because many agencies have specified orange for decades. It is one of the two MUTCD roadway colors, so a flagger, a paver or a line crew may wear either; the employer chooses. Off the road, orange is as much a hi-vis color as lime, and the orange-vs-yellow guide linked below goes through the visibility science.
What do different colour hi-vis jackets mean?
Under the standard, nothing beyond the class: yellow-green, orange-red and red are equal. The meanings people see on sites are conventions a company or a site adopts so a supervisor can read a crew at a glance: orange for traffic control, lime for the general crew, blue for visitors or new workers, white for engineers and inspectors, green for safety or first aid, red for fire wardens, black for security. None of it is in the MUTCD or OSHA; a site that uses a scheme posts it.
Who wears a blue and yellow hi-vis vest on site?
Under a color scheme, usually a visitor, a new worker, a supervisor or a medical responder; the blue tells the crew who is new or in charge, and the yellow keeps the wearer visible. Two garments answer the question: a Non-ANSI vest in blue with lime trim (Kishigo’s Enhanced Visibility Series), for a site with no vehicle hazard, and a Class 2 lime vest with a royal blue contrast (the S5042 surveyor vest), which keeps its label because the contrast strip is not part of the counted area.
Is pink hi-vis "OSHA approved"?
OSHA does not approve colors or garments. ANSI/ISEA 107-2020 names three background colors, fluorescent yellow-green, fluorescent orange-red and fluorescent red, and the MUTCD (11th Edition, section 6C.05) allows fluorescent orange-red, fluorescent yellow-green or a combination of the two in a work zone. A pink vest is not one of those colors, so it cannot be labeled to a 107 class and does not satisfy the MUTCD; off the roadway an employer may issue one where its hazard assessment finds no need for a class. ML Kishigo makes its pink styles as enhanced-visibility garments and labels them Non-ANSI.
What is the hex code for a yellow safety vest?
There is none in the standard. ANSI/ISEA 107 defines fluorescent yellow-green by chromaticity coordinates and a minimum luminance factor measured on the fabric itself, not by a screen color; the hex values people quote (a lime-yellow in the FFFF00 to CCFF00 range) are approximations of a fluorescent pigment a screen cannot reproduce, because a screen cannot fluoresce. For a logo or a drawing any of them will do; for a garment, the label is the test.
What color are hi-vis shirts?
The same three 107 background colors as vests: fluorescent yellow-green (lime), fluorescent orange-red and fluorescent red. ML Kishigo’s Class 2 and Class 3 shirts come in lime and orange, with black-bottom versions that keep the hi-vis color on the upper body, where the standard counts it, and put black where the dirt lands. A shirt in any other color is not a hi-vis shirt under the standard.
Is black hi-vis legal?
A black-bottom vest or shirt with the fluorescent color and the tape on the upper body can carry a Class 2 or 3 label, because the standard counts the fluorescent and retroreflective area and does not care about the color of the rest; ML Kishigo labels its Premium Black Series Type R Class 2 or Class 3. An all-black garment with reflective tape is Non-ANSI, allowed off the roadway where no class is required, never in a work zone.
Does OSHA require a particular vest color?
OSHA requires hi-vis through 1926.201 and the MUTCD on roadways and through the hazard assessment under 1910.132 elsewhere, and leaves the color to the standard and the employer; Cal/OSHA 1598 and 1599 do the same. The only color rule a crew meets is the MUTCD’s: fluorescent orange-red, fluorescent yellow-green or a combination, in the right-of-way.
Can safety vests be red?
Fluorescent red is a 107 background color and ML Kishigo makes Class 2 vests in it; it is not one of the two MUTCD roadway colors, so it is for sites off the right-of-way. A plain red vest (Kishigo’s B103, B122) is Non-ANSI.
Why is a surveyor’s vest lime with a colored stripe?
So crews can be told apart without losing the class: the S5042, S5043, S5044 and S5046 are lime Class 2 surveyor vests with a royal blue, red, green or pink contrast strip under the tape, which Kishigo calls "color contrast". The lime does the hi-vis work; the stripe is identification.
In plain words
- Three hi-vis colors: fluorescent yellow-green, fluorescent orange-red and fluorescent red. The MUTCD allows the first two on the roadway.
- The standard assigns no color to a trade; orange on road crews and lime on construction is practice, and blue, white, green, red and black schemes are site conventions.
- Pink, blue, white, green, plain red, gray, purple and black vests are Non-ANSI; ML Kishigo sells them for visitors and non-traffic sites.
- A lime vest with a colored contrast strip, or a black bottom, keeps its class; the colored part is not counted.
Questions people ask
What are the three hi-vis colors?
Fluorescent yellow-green, fluorescent orange-red and fluorescent red, the background colors ANSI/ISEA 107 sets performance limits for; the MUTCD allows the first two in a work zone.
Is orange or lime better for a road crew?
Both satisfy the MUTCD; orange reads against green roadside vegetation and yellow-green equipment, lime is brighter in daylight, and the employer chooses.
Is a pink safety vest allowed?
As a Non-ANSI garment where no class is required; it cannot carry a 107 class and is not a MUTCD roadway color. ML Kishigo labels its pink vests Non-ANSI.
What does a blue safety vest mean?
Nothing under the standard; on sites with a color scheme it usually marks a visitor, a new worker or a supervisor. ML Kishigo’s blue vests are Non-ANSI.
What does a white safety vest mean?
A site convention, often an engineer, inspector or supervisor; no class attaches to white.
Are black safety vests hi-vis?
A black-bottom vest with fluorescent material and tape on the upper body can be Class 2 or 3; an all-black vest with tape is Non-ANSI.
Is there a hex code for safety orange or safety yellow?
Not in the standard, which defines the colors by measured chromaticity and luminance on the fabric; screen hex values are approximations.
Does OSHA approve vest colors?
No; OSHA does not approve products or colors. The MUTCD sets the roadway colors and the employer selects the garment.
Related guides
Are yellow or orange safety vests better?What ANSI/ISEA 107 and the MUTCD sayWhat is enhanced visibility clothing?And why it is not Class 1, 2 or 3Why do workers wear hi-vis vests?Is it required, and can you wear black hi-visWhat are the levels of safety vests?Class 1, 2, 3 and E, Type R, O and PWhat is a surveyor’s safety vest?Surveyor, breakaway, X-back and black bottom vestsDoes OSHA require high-visibility clothing?The rules that call for itHi-vis for flaggers and roadway workWhat the MUTCD requiresANSI/ISEA 107 High-Visibility Safety ApparelThe rule pageThe ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.
© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.
