Skip to main content
Home › Guides › Eye and face › Cleaning lenses
Guide · Eye protection · Manufacturer lens care data · 29 CFR 1910.132(a)

Bayshore Safety & Industrial Supplies Guide

How do you clean safety glasses without scratching them? Lens wipes and alcohol, anti-reflective and anti-fog coatings and household cleaners, yellowed and scratched lenses, and scratch-resistant hard coats

Rinse first, then wash with the solution the manufacturers sell for the purpose or with mild soap and lukewarm water, and dry with a low-lint lens tissue or a clean microfiber cloth; never dry-wipe a dusty lens, because the grit is what scratches polycarbonate. The lens cleaning stations from MCR Safety, Radians, Bouton Optical and UVEX exist for exactly this: MCR Safety states its solution is for plastic, polycarbonate and glass lenses and is silicone free, and Radians states its towelette formula cleans greasy and oily glasses, leaves an anti-fog and anti-static coating, and uses a low-lint, non-abrasive tissue. Ammonia glass cleaners, acetone, paper towels and shirt tails are the things that take coatings off. A scratched lens cannot be repaired; a lens that has yellowed has aged in UV and is replaced.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · Radians lens cleaning station and towelette texts (“clean greasy and oily glasses while providing an anti-fog / anti-static coating. Low lint, non-abrasive tissue”; radians.com); MCR Safety LCS1, LCS2, LCT and LFT600 texts (“for plastic, polycarbonate and glass lenses”, silicone free, pre-moistened anti-fog wipes; mcrsafety.com); PIP Rich Product Data, October 2026 (Bouton Optical and UVEX lens cleaning stations, silicone free; Duramass, MAX3, Ultra-Dura and Anti-Scratch hard coats as named); Portwest EN 166 K mark (abrasion resistance) as printed; ANSI/ISEA Z87.1-2020 Table 3; 29 CFR 1910.133 and 1910.132(a) (PPE maintained in a sanitary and reliable condition); Liberty Safety product pages and spec sheets (libertysafety.com, read Nov 11 2026)
MCR Safety LCS1 Safety Glasses Accessories, Disposable Lens CleaningMCR Safety LCS1 Safety Glasses Accessories, Disposable Lens CleaningMCR Safety states the LCS1 solution is for plastic, polycarbonate and glass lenses and is silicone free; 8 oz pump bottle and 600 tissues

Why cleaning is part of the rule. 29 CFR 1910.132(a) says protective equipment shall be maintained in a sanitary and reliable condition, and 1910.133 requires the eye protection to be worn; a lens so smeared or scratched that the wearer takes it off meets neither. Polycarbonate is chosen for safety lenses because it is tough against impact, but it is soft against abrasion, which is why every manufacturer sells a hard coat (MCR Safety Duramass and MAX3, UVEX Ultra-Dura, Bouton Optical Anti-Scratch, Portwest’s EN 166 K mark) and why the way a lens is wiped decides how long it lasts. This page collects what the manufacturers state about cleaning and coatings, and answers the questions about alcohol, Windex, yellowing and scratches that come with them.

Cleaning and coating questions, one by one

Statements in quotation marks are the manufacturers’ own, from the product pages on this site.

What is the right way to clean safety glasses?Rinse the lens under running water or with the station solution to float the grit off before anything touches it; wash with the cleaning solution or a drop of mild soap in lukewarm water, working the frame and nose pads too; rinse; dry with a low-lint lens tissue or a clean microfiber cloth, blotting rather than scrubbing. Radians describes its station tissue as “low lint, non-abrasive” and states that “strategically placed stations will promote proper lens cleaning techniques extending the life of prescription and non-prescription safety glasses”. The two mistakes that end a lens are dry-wiping a dusty lens and drying it with a paper towel.
Are lens wipes just alcohol wipes, and can I use 70 percent isopropyl alcohol?Not the same thing. Lens towelettes from Radians and MCR Safety are a cleaning solution formulated for polycarbonate on a low-lint tissue; Radians states its formula also leaves “an anti-fog / anti-static coating”, which an alcohol wipe does not. Isopropyl alcohol itself does not attack polycarbonate at the strengths sold for first aid and electronics, and the cleanroom wipes PIP sells are 70 percent IPA, but alcohol strips temporary anti-fog films and can shorten the life of some coatings, and it dries fast enough to leave streaks on a tinted lens. The manufacturers’ own solutions are what they name for their lenses; Radians also lists an alcohol-free cleaning wipe for respirators.
Will Windex or another glass cleaner remove an anti-reflective coating?Household glass cleaners are made for glass and often contain ammonia, which the lens manufacturers treat as a solvent to keep off coated plastic: it dulls anti-reflective coatings over repeated use and strips surfactant anti-fog films at once. Bouton Optical sells its Captain, Commander and Sunburst lenses with an Anti-Reflective coating as a separate version, and those are the lenses to keep away from ammonia. MCR Safety states its station solution is for plastic, polycarbonate and glass, which is the point of a purpose-made solution: it is safe on all three. Acetone and other solvents craze polycarbonate and are never used on a lens.
Can you fix scratches on safety glasses?No. A scratch in polycarbonate is a groove; the home remedies (toothpaste, baking soda, polish) are abrasives that take the hard coat off around the groove and leave a hazy patch that scatters light worse than the scratch. A scratched lens that is in the line of sight is replaced; a lens with a replaceable-lens frame (Radians LPX goggle, MCR Safety Hydroblast HB3, Dagger and Cloak goggle lenses) is re-lensed. Z87.1 marks are on the lens, and a lens so worn that the wearer looks around the damage no longer gives the protection the mark describes.
Which brand of safety glasses is the most scratch-resistant?No manufacturer publishes a comparative scratch test, so the honest answer is the coating name and the European mark. MCR Safety sells the Duramass scratch-resistant hard coat and the MAX3 hard coat; UVEX the Ultra-Dura hardcoat; Bouton Optical an Anti-Scratch coating on most lenses; Radians states IQuity is anti-scratch as well as anti-fog; Portwest prints the EN 166 K mark (resistance to surface damage by fine particles) on the PS23 and others. “Scratch-proof” and “scratchless” do not exist on a polycarbonate lens; scratch-resistant is the claim, and the cleaning method decides how long it holds.
How do you remove yellowing from lenses?You do not; a yellowed polycarbonate lens has been aged by ultraviolet and heat (a dashboard is the classic cause) and the color change is in the material. If a clear lens looks yellow, confirm it is not an amber lens (Radians, MCR Safety and Portwest sell amber in the same frames) and then replace it. Yellowing on a frame or on the elastomer of a goggle is the same aging. Storing eyewear in its pouch or a case out of the sun, which the manufacturers include with the premium styles, is what delays it.
Do anti-fog wipes and anti-fog coatings survive cleaning?A factory anti-fog coating (MCR Safety MAX6 and UV-AF, Radians IQuity, UVEX Hydroshield, Bouton Optical FogLess 3Sixty) is bonded to the lens and survives washing with the station solution or mild soap; it does not survive abrasive wiping, ammonia or solvent. A wipe-on anti-fog treatment (MCR Safety LFT600 towelettes, the Radians station formula) is a film that is renewed each time the lens is cleaned with it and removed by anything else. If a coated lens starts to fog like an uncoated one, the coating has been worn or washed off and the lens is at the end of its life.
How do you clean goggles and face shields, and how often?The same way, with more attention to the body: the elastomer or PVC of a goggle holds sweat and dust, so the frame is washed in the soapy water and the strap wiped; a face shield window is rinsed and blotted exactly like a lens, because its polycarbonate or PETG scratches the same way, and a shield used over welding or grinding is checked for pits that cannot be cleaned out. 1910.132(a) sets the standard (sanitary and reliable condition); the frequency is at least daily for shared eyewear and whenever vision is impaired, which is the cleaning-station habit the manufacturers describe.
Why do my eyes hurt when I wear safety glasses?The manufacturers do not address this medically, and neither does this page; the mechanical causes a safety supplier sees are a smeared or scratched lens that makes the eye work to see through it, a frame with the wrong base curve for the face so the lens sits at an angle, a bifocal (reader) lens worn for distance work, and a tinted lens worn indoors. Clean the lens first; if the strain stays, the fit and the lens choice are the next things to change, and persistent eye pain is for a doctor.

What the cleaning and coating words mean

The vocabulary of lens care, as the manufacturers use it.

  • Hard coat (anti-scratch): a harder layer over soft polycarbonate. MCR Safety Duramass and MAX3; UVEX Ultra-Dura; Bouton Optical Anti-Scratch; Radians IQuity (anti-scratch as well as anti-fog). It is why a dry wipe with grit matters.
  • K (EN 166): the European mark for resistance to surface damage by fine particles, printed by Portwest beside F/FT and N.
  • Anti-reflective (AR): a coating that cuts reflections off the lens surface; sold as a separate version by Bouton Optical. Dulled by ammonia cleaners over time.
  • Anti-fog, factory and film: a bonded coating (MAX6, IQuity, Hydroshield, FogLess 3Sixty) versus a wipe-on film from a towelette (MCR Safety LFT600, the Radians station formula). The first survives washing; the second is renewed by it.
  • Silicone free: printed on the MCR Safety and Bouton Optical station solutions. Silicone residue interferes with paint and coatings in a finishing shop, which is why the solutions are made without it.
  • Low-lint, non-abrasive tissue: the station tissue Radians describes; the alternative is a clean microfiber cloth. Paper towels are wood fiber and abrasive.
  • Anti-static: Radians states its station formula leaves an anti-static coating, which keeps dust from clinging to the lens between cleanings.
  • Yellowing: UV and heat aging of polycarbonate; not removable. Storage in a pouch or case out of the sun delays it.
Radians, MCR Safety, PIP (Bouton Optical, UVEX) and Portwest product pages on this site; ANSI/ISEA Z87.1-2020 Table 3 and EN 166 marks as printed.
What to use and what to keep off a safety lens
Product or methodWhat the manufacturers stateSafe on polycarbonate?Effect on coatings
Lens cleaning station solutionMCR Safety: for plastic, polycarbonate and glass; silicone free. Radians: cleans greasy and oily lenses, leaves anti-fog / anti-static coatingYesPreserves factory coatings; renews wipe-on anti-fog
Pre-moistened lens towelettesRadians LCD100, LC25BG; MCR Safety LCT and LFT600 (anti-fog)YesAs above
Mild dish soap and lukewarm waterNot a manufacturer statement; the general lens-care methodYesSafe on factory coatings if rinsed
70% isopropyl alcoholSold by PIP as cleanroom wipes; not named for eyewear by the lens manufacturersDoes not attack the lensStrips wipe-on anti-fog films; streaks tints
Ammonia glass cleanerNot named by any lens manufacturerAvoidDulls anti-reflective coatings; removes anti-fog films
Acetone and solventsNot namedNo; crazes polycarbonateDestroys
Paper towel, shirt tail, dry wipeRadians specifies low-lint, non-abrasive tissue insteadScratchesWears coatings off
Toothpaste or polish on scratchesNot namedAbrasive; removes hard coatDestroys

A specific lens may carry its own care instruction on its package; that instruction governs.

Source: Manufacturer statements as published on this site; the general chemistry of polycarbonate as every lens manufacturer’s care sheet gives it.

Questions people ask

How do you clean safety glasses without scratching them?

Rinse the grit off first, wash with a lens solution or mild soap and lukewarm water, and blot dry with a low-lint lens tissue or microfiber. Never dry-wipe a dusty lens or dry it with a paper towel.

Are glasses wipes just alcohol wipes?

No. Radians and MCR Safety lens towelettes are a lens-cleaning solution on a low-lint tissue; Radians states its formula leaves an anti-fog and anti-static coating. An alcohol wipe cleans but strips anti-fog films and streaks tints.

Can you use 70 percent isopropyl alcohol to clean glasses?

It does not attack polycarbonate, but it removes wipe-on anti-fog films and can shorten coating life; the lens manufacturers name their own solutions instead. Use it on frames and straps if anything.

Will Windex remove anti-reflective coating?

Ammonia-based glass cleaners dull anti-reflective coatings with repeated use and remove anti-fog films at once; they are made for glass. Use a lens solution the manufacturer states is for polycarbonate.

Can you fix scratches on safety glasses?

No. Polishing with toothpaste or baking soda removes the hard coat and leaves haze. Replace the lens; several goggles have replaceable lenses.

Which brand of safety glasses is the most scratch-resistant?

No manufacturer publishes a comparison. The named hard coats are MCR Safety Duramass and MAX3, UVEX Ultra-Dura, Bouton Optical Anti-Scratch and Radians IQuity; Portwest prints the EN 166 K abrasion mark. Cleaning method decides how long any of them lasts.

Are there scratch-proof or scratchless glasses?

Not in polycarbonate. The claim is scratch-resistant, a hard coat over a soft lens.

How do you remove yellowing from glasses lenses?

You cannot; it is UV and heat aging of the polycarbonate. Check that the lens is not an amber tint, then replace it, and store eyewear out of the sun.

Do anti-fog lens wipes actually work?

Yes, as a renewable film; MCR Safety LFT600 towelettes and the Radians station formula leave an anti-fog layer that lasts hours and is renewed at each cleaning.

What ingredients are in lens cleaning solution?

The manufacturers do not publish formulas on the product pages; what they state is the scope (plastic, polycarbonate and glass), silicone free, and for Radians, that the formula leaves an anti-fog and anti-static coating.

How often should safety glasses be cleaned?

29 CFR 1910.132(a) requires PPE to be kept in a sanitary and reliable condition; in practice at least daily, at every shift change for shared eyewear, and whenever the lens is smeared enough to impair vision.

Can I use alcohol wipes on polarized sunglasses?

Polarized Z87 lenses are polycarbonate with a polarizing layer and usually a mirror or hard coat; the lens manufacturers name their own solutions. Alcohol streaks dark tints and is hard on some mirror coatings.

What is a lens cleaning station?

A wall or table dispenser with a bottle of lens solution and boxes of low-lint tissues (MCR Safety LCS1: 8 oz pump and 600 tissues; LCS2: 16 oz spray; Radians LCS; Bouton Optical 252-LCS08; UVEX S483 portable).

Why do my eyes hurt when I wear safety glasses?

From the supplier’s side: a smeared or scratched lens, a frame that sits at the wrong angle, a reader lens worn for distance, or a tint worn indoors. Clean, then refit. Persistent pain is a medical question.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Outfitting a crew with eye protection?Call (925) 215-7337 or email us the work and the quantities and we will quote glasses, goggles and face shields by the dozen with the manufacturer’s marks listed.
Eye protection selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.