Skip to main content
Home › Guides › Eye and face › What goggles are for
Guide · Eye protection · ANSI/ISEA Z87.1 D3, D4 and D5 · 29 CFR 1910.133 · 1910.1450

Bayshore Safety & Industrial Supplies Guide

What are safety goggles for? Chemistry lab and splash goggles, dust goggles, the Z87.1 D3, D4 and D5 marks, what happens without them, and why safety glasses are not a substitute for goggles

Safety goggles seal to the face. That is the whole difference from safety glasses, and it is why 29 CFR 1910.133 and the selection chart in Appendix B put goggles on the hazards that go around a lens: liquid splash from acids, caustics and solvents, chemical gases and vapors, dust and fine dust, and the flying chips of chipping, grinding and masonry where glasses alone leave a gap. ANSI/ISEA Z87.1 marks the hazard a goggle was tested for on the lens or frame: D3 for splash and droplets, D4 for dust, D5 for fine dust. A chemistry lab goggle is an indirect-vent D3 goggle; a dust goggle is a direct-vent or sealed D4 or D5 goggle; and there is no substitute for either when the hazard is one of those, because the rule names the hazard, not the comfort.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · 29 CFR 1910.133(a)(1) and 1926.102(a)(1) (ecfr.gov, Nov 9 2026; src/); 29 CFR 1910 Subpart I Appendix B (eye and face protection selection chart) as the live Z87 guides quote it; ANSI/ISEA Z87.1-2020 Table 3 (D3 splash and droplet, D4 dust, D5 fine dust) as the manufacturers print it; MCR Safety 22, 23 Stryker and 24 Verdict goggle pages (D3 splash, D4 dust; mcrsafety.com); Radians CS01 and GG chemical splash goggle pages (“ANSI Z87.1 and D3 droplet tested goggle fits over most prescription eyewear”; radians.com); PIP Rich Product Data, October 2026 (UVEX A600 and Avatar Plus indirect-vent goggles, Bouton Optical 440/550 direct, indirect and non-vented bodies); 29 CFR 1910.1450 (laboratory standard) as the live chemical PPE guide quotes it; Liberty Safety product pages and spec sheets (libertysafety.com, read Nov 11 2026)
Radians CS01 Chemical Splash Safety GoggleRadians CS01 Chemical Splash Safety GoggleRadians states the CS01 is an “ANSI Z87.1 and D3 droplet tested goggle” with indirect vents that “fits over most prescription eyewear”

What the rule says goggles are for. 29 CFR 1910.133(a)(1) requires eye or face protection when exposed to flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation; 1926.102(a)(1) says the same for construction. The non-mandatory selection chart in 1910 Subpart I Appendix B then matches the hazard to the device: spectacles with side protection for flying fragments; goggles with eyecups or cover goggles for chipping, grinding and masonry; goggles for liquid splash (with a face shield for severe exposure), for irritating mists and for dust; and special-purpose goggles for chemical gases and vapors. Z87.1 gives the goggle a mark for each of those tests, and the manufacturers print the mark: MCR Safety’s 22, 23 Stryker and 24 Verdict carry D3 splash and D4 dust; Radians’ CS01 and GG carry D3. The cards below answer the purpose questions, from the lab bench to the demolition saw.

What goggles do, hazard by hazard

Marks are the manufacturers’ own as printed on the product pages on this site; the rule text is 29 CFR 1910.133 and Appendix B.

What is the purpose of safety goggles, in one sentence?To put a sealed barrier between the eye and a hazard that would get around a safety glass lens: a splash, a cloud of dust, a vapor, or a chip coming from below or the side. A safety glass stops a particle flying straight at the lens and is tested for that (Z87 or Z87+); a goggle is tested for the hazards that flow, splash or drift, and marked D3, D4 or D5 when it passes. The seal is also why goggles fog more and why the anti-fog versions exist.
What is the function of safety goggles in a laboratory, and what kind do you need for chemistry?A laboratory goggle is an indirect-vent chemical splash goggle: the vents are hooded or baffled so air moves through but a liquid running down the lens cannot, and the body seals around the eyes so a splash from the side or a bottle that bursts at bench height does not reach the eye. In Z87.1 terms it is a D3 (splash and droplet) goggle; MCR Safety prints D3 on the 22, 23 Stryker and 24 Verdict, Radians prints D3 on the CS01 and GG, and UVEX lists the A600 and Avatar Plus as indirect-vent splash goggles that fit over prescription glasses. OSHA’s laboratory standard, 1910.1450, requires the chemical hygiene plan to set out the protective equipment for the work; the PPE rule, 1910.133, supplies the device. Chemistry goggles are the same goggle a plant uses for acids and caustics.
What type of eye protection protects from dust, and what are D4 and D5?A goggle, because dust drifts around a lens. Z87.1 tests goggles against dust and marks them D4, and against fine dust (the particles that stay suspended) and marks them D5; a D5 goggle is normally non-vented or has filtered vents. MCR Safety prints D4 dust on its 22, 23 and 24 goggles. For coarse dust and chips in airflow, a direct-vent goggle (Bouton Optical 440 Basic, 550 Softsides direct-vent) breathes most and fogs least; for fine dust, the sealed or indirect design. Foam-lined sealed eyewear (Radians Mirage Foam, Crossfire Shield, MCR Safety Reaper) sits between glasses and goggles: a foam gasket cuts the gap for wind and dust, and the manufacturers list them as Z87.1+ eyewear, not as D-marked goggles unless the page says so.
What is the most effective eye protection against flying debris?For a particle flying straight at the face, a Z87+ high-impact lens, glasses or goggles alike; the + means the lens and frame passed the high-velocity and high-mass tests. For debris from a grinder, chipping hammer or masonry saw, Appendix B lists goggles (eyecup or cover) because chips come from below and the side, and it lists a face shield over the goggles for severe exposure. Z87.1 marks the impact level, not the hazard, so a goggle that is also D3 or D4 covers the splash and dust that come with the same job. A face shield alone is never the answer; 1910.133 treats it as secondary protection over glasses or goggles, which the live face shield guide explains.
Is there a substitute for safety goggles?Not when the hazard is one that goes around a lens. Side-shield glasses are a substitute for goggles only in the flying-particle row of the Appendix B chart; for liquid splash, mists, dust and vapors the chart lists goggles and nothing else, with a face shield added on top for severe splash. The things people ask about as substitutes (regular glasses, a face shield alone, prescription glasses, sunglasses) each fail a different way: regular and prescription glasses are not Z87-marked and have no side or seal, a face shield has an open bottom, and none of them are D3 or D4. The one legitimate variation is a goggle that fits over prescription glasses, which Radians, MCR Safety (Hydroblast HB3 OTG) and UVEX (A600) sell for exactly that.
What happens if you don’t wear safety goggles in a lab or a shop?The injuries the rule lists happen to the eye: a chemical burn from a splash (acids and caustics damage the cornea in seconds, which is why 1910.151(c) requires an eyewash where the eyes may be exposed to corrosives), an abrasion or embedded particle from dust and chips, and irritation from vapor. The regulatory consequence is a citation under 1910.133 or 1926.102 for the employer, who is required to ensure the protection is worn, and under 1910.1450 in a laboratory whose chemical hygiene plan calls for goggles. Appendix B’s own words are that the protection shall be matched to the hazard, and a bench with open acids is a splash hazard whether or not anything has splashed yet.
Which form of exposure do goggles protect against that glasses do not?Anything that is not a straight-line projectile: liquid splash and droplets (D3), dust (D4), fine dust (D5), and, with a non-vented body, gases and vapors. Glasses protect against the frontal impact Z87.1 tests them for and, with side shields, against particles from the side; they have no seal at the brow, the cheek or the temple, so a splash, a mist or a dust cloud reaches the eye. Molten metal and welding light have their own devices (face shields and filter lenses), which the welding guides cover.
What are science lab goggles called, and how much do they cost?Chemical splash goggles, or indirect-vent goggles; in the standard’s language, D3 goggles. On this site the basic indirect-vent splash goggles from Radians (CS01, GG) and MCR Safety (22) are a few dollars each, the anti-fog versions a little more (MCR Safety 23 Stryker, 24 Verdict; UVEX A600 and Avatar Plus), and the prices on the product band below are live. A lab buying by the case gets the case price on the product page; a student buying one gets the same goggle.
What goggles do welders wear, and are laser goggles the same thing?Welding goggles are cup or cover goggles with a filter lens of the shade number 1910.133(a)(5) requires for the process (W marked in Z87.1); they are for gas welding, brazing and cutting, where the arc is small enough that a helmet is not needed, and the live welding shade guide has the table. Laser eyewear is a different device tested to a different standard (ANSI Z136) for the laser’s wavelength and power, and it is not a Z87.1 D-marked goggle; nothing on this site is sold as laser protection. Shade 5 cutting goggles are not laser goggles.

The goggle vocabulary

The words on a goggle and in the rule, in order.

  • D3 (splash and droplet): the Z87.1 mark for a goggle that passed the liquid splash and droplet test; the chemistry lab and acid-handling goggle. Printed by MCR Safety and Radians on the goggles above.
  • D4 (dust): the mark for a goggle that passed the dust test. D5 (fine dust): the mark for the fine-dust test; normally a sealed or filtered-vent goggle.
  • Indirect vent: hooded or baffled vents that pass air but not liquid; the splash goggle design. Direct vent: open perforations that pass air freely; the dust-and-chip goggle that fogs least. Non-vented: sealed; for gases, vapors and fine dust; fogs most.
  • Eyecup and cover goggle: the Appendix B terms for a goggle that seals each eye separately and one that covers both, and fits over glasses.
  • OTG (over the glass): a goggle or spectacle sized to fit over prescription glasses; Radians CS01 and GG, MCR Safety Hydroblast HB3, UVEX A600 are listed that way.
  • Z87 and Z87+: the basic and high-impact marks; on a goggle they appear beside the D marks.
  • Foam-lined sealed eyewear: safety glasses with a foam gasket that closes the gap to the face; listed as Z87.1+ eyewear, not as D-marked goggles unless stated.
  • Secondary protection: 1910.133’s treatment of a face shield, worn over glasses or goggles, never alone.
ANSI/ISEA Z87.1-2020 Table 3 as the manufacturers print it; 29 CFR 1910.133 and 1910 Subpart I Appendix B.
Appendix B selection chart, the rows that call for goggles
Hazard (Appendix B wording)Protection listedZ87.1 mark to look forExamples on this site
Chipping, grinding, machining, masonry work, woodworking, sawing, drilling, chiseling, powered fastening, riveting, sanding: flying fragments, objects, large chips, particles, sand, dirtSpectacles with side protection, goggles, face shields; for severe exposure, use face shieldZ87+ impact; D4 if dustBouton Optical 440/550 direct-vent; Radians Mirage Foam; MCR Safety 22
Chemical handling: splashGoggles, eyecup and cover types; for severe exposure, use face shieldD3Radians CS01, GG; MCR Safety 22, 23 Stryker, 24 Verdict; UVEX A600, Avatar Plus
Chemical handling: irritating mistsSpecial-purpose gogglesD3 (non-vented)Bouton Optical 552 non-vented
Dust: nuisance dustGoggles, eyecup and cover typesD4 or D5MCR Safety 22, 23, 24 (D4 printed); sealed goggles
Welding, gas: glare and sparksWelding goggles or welding face shield, shade 4 to 6W with shade numberWelding PPE selector
Chemical gases or vapors (1910.133(a)(1))Non-vented goggle, with respiratory protection as the hazard requiresD3, non-ventedNon-vented goggles

The chart is guidance; the employer’s hazard assessment under 1910.132(d) decides the device.

Source: 29 CFR 1910 Subpart I Appendix B, Eye and Face Protection Selection Chart (non-mandatory), as summarized; marks per ANSI/ISEA Z87.1-2020 Table 3 as the manufacturers print them.

Questions people ask

What is the purpose of goggles?

To seal the eye off from hazards that get around a lens: splash, dust, vapor and chips from the side. Glasses stop a frontal projectile; goggles are tested and marked for the rest (D3 splash, D4 dust, D5 fine dust).

What is the function of safety goggles in a laboratory?

Splash protection. A lab goggle is an indirect-vent D3 goggle whose hooded vents pass air but not liquid, sealed to the face so an acid or solvent splash from any angle does not reach the eye.

What kind of goggles do you need for chemistry?

Indirect-vent chemical splash goggles marked D3 (Radians CS01 and GG, MCR Safety 22, 23 Stryker, 24 Verdict, UVEX A600 and Avatar Plus). The anti-fog versions are the ones that stay on.

What are science lab goggles called?

Chemical splash goggles or indirect-vent goggles; D3 goggles in Z87.1 language.

What type of eye protection is used to protect from dust?

Goggles. Z87.1 marks dust-tested goggles D4 and fine-dust goggles D5; MCR Safety prints D4 on its 22, 23 and 24 goggles. Direct-vent goggles breathe most; sealed goggles stop fine dust.

What is the most effective type of protective eyewear to protect from flying debris?

A Z87+ high-impact lens, and for grinding, chipping and masonry Appendix B lists goggles, with a face shield over them for severe exposure, because chips come from below and the side.

Is there a substitute for safety goggles?

Not for splash, dust, mist or vapor; the Appendix B chart lists goggles alone for those. Side-shield glasses substitute only for frontal flying particles. A face shield alone never does.

What happens if you don’t wear safety goggles?

Chemical burns to the cornea from splash, embedded particles and abrasions from dust and chips, irritation from vapor; and a citation under 1910.133 or 1926.102 for the employer who did not ensure they were worn.

What happens if you don’t wear goggles in a lab?

The same injuries, with corrosives the main risk; 1910.1450 requires the chemical hygiene plan to set the PPE, and 1910.151(c) requires an eyewash where eyes may be exposed to corrosives.

Which form of exposure do goggles protect against?

Liquid splash and droplets, dust and fine dust, and with a non-vented body, gases and vapors; plus the impact the Z87 or Z87+ mark covers.

Which eye protection covers the entire face?

A face shield; 1910.133 treats it as secondary protection worn over glasses or goggles because the bottom is open. The live face shield guide covers when it is required.

How much do safety goggles cost?

Basic indirect-vent splash goggles from Radians and MCR Safety are a few dollars each; anti-fog and over-the-glass versions a little more. Current prices are on the product list on this page.

What goggles do welders wear?

Cup or cover goggles with a W-marked filter lens of the shade 1910.133(a)(5) requires, for gas welding, brazing and cutting; arc welding uses a helmet. The welding shade guide has the table.

Do laser goggles work, and are they the same as safety goggles?

Laser eyewear is tested to ANSI Z136 for a specific wavelength and power and is not a Z87.1 D-marked goggle; nothing on this site is laser protection.

Can safety goggles be worn over prescription glasses?

Yes, the over-the-glass styles: Radians CS01 and GG, MCR Safety Hydroblast HB3, UVEX A600 are listed by their manufacturers as fitting over most prescription eyewear.

How do I clean lab goggles?

Rinse, wash with lens solution or mild soap, blot dry with a low-lint tissue; wash the body and strap too. The live cleaning guide covers coatings and what to keep off the lens.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Outfitting a crew with eye protection?Call (925) 215-7337 or email us the work and the quantities and we will quote glasses, goggles and face shields by the dozen with the manufacturer’s marks listed.
Eye protection selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.