Skip to main content
Home › Guides › Hand protection › Cleaning work gloves
Guide · Hand protection · Care and replacement

Bayshore Safety & Industrial Supplies Guide

How do you clean work gloves, and how often should you replace them? Washing coated knit, cotton, gardening and mechanics gloves, machine washing and drying, getting the smell out, oil-soaked gloves, and when a work glove is done

Most work gloves can be washed, and the manufacturers say which ones: cotton, jersey and string knit gloves launder (MCR Safety prints "good for laundering" on its jersey gloves), coated knit and cut-resistant gloves take a warm machine wash and air-dry (MCR Safety now sells its CutPro knits for "machine wash longevity"), pigskin "doesn’t lose its shape or function when laundered" while cowhide "stiffens when it gets wet", and disposable gloves are not washed at all. The rule for every glove is the same: wash it the way its manufacturer states, air-dry it, and replace it when the protective layer is gone, which is when the coating is cracked or worn through, the leather is cut or hard, the knit is holed, or the smell will not leave. OSHA’s PPE training rule, 1910.132(f), requires employees to be taught "the proper care, maintenance, useful life and disposal of the PPE", and 1910.132(e) says "defective or damaged personal protective equipment shall not be used"; the manufacturer’s care statement is what both point to.

Bayshore Safety. Industrial safety and PPE supplier since 2017. · Current as of November 2026 · Liberty Safety product pages, spec sheets and category pages (libertysafety.com, read Nov 11 2026); MCR Safety product pages and leather-type statements (mcrsafety.com, saved Nov 7 2026); 29 CFR 1910.132 Personal protective equipment, general requirements (eCFR, saved Nov 9 2026); 29 CFR 1910.138 Hand protection (eCFR, saved Nov 9 2026); Armor Guys product pages, spec sheets, catalog C.009 and workbook C.010 (armorguys.com, read Nov 12 2026)
Liberty Safety FLX 4631QBK Grip Gloves, Nitrile Coated, 13 Gauge, Black, 5 SizesLiberty Safety FLX 4631QBK Grip Gloves, Nitrile Coated, 13 Gauge, Black, 5 SizesLiberty Safety prints 13 gauge polyester shell, black nitrile palm coating, EN 388 4121; sold by the dozen

Why the care question is a safety question. A glove protects with a layer: a nitrile or polyurethane film on a knit, a tanned hide, a high-strength yarn, a cotton pile. Washing it wrong strips or stiffens that layer; not washing it lets oil, sweat and grit degrade it and breed the smell. OSHA’s general PPE rule says equipment must be "maintained in a sanitary and reliable condition" (1910.132(a)) and that "defective or damaged personal protective equipment shall not be used" (1910.132(e)); the training rule (1910.132(f)) lists "the proper care, maintenance, useful life and disposal of the PPE" among the things every employee who wears PPE must be taught. The manufacturer’s care statement is the document that answers all three, and this guide collects what the manufacturers whose lines we carry print, glove type by glove type. Where a manufacturer prints nothing, the honest answer is "wash it warm, air-dry it, and inspect it", and that is what is written here.

Glove by glove: what the manufacturers print about washing

Each statement is the manufacturer’s own; where a line prints no care statement the entry says so.

Cotton, jersey, canvas and string knitLaunderable. MCR Safety prints "good for laundering" on its brown jersey gloves; Liberty Safety lists "reusability" as a feature of its cotton line. Machine wash warm, tumble or air-dry; expect some shrinkage from hot water and a hot dryer, so a laundering crew buys a size up.
Coated knit gloves (polyurethane, nitrile, latex, foam)Machine washable in warm water on a gentle cycle with a mild detergent; air-dry. Heat (a hot dryer, a radiator) and solvents crack or lift the coating, bleach degrades latex and nitrile films. MCR Safety sells its CutPro cut-resistant knits for "machine wash longevity" and "durability through multiple washes".
Cut-resistant glovesThe same as coated knits, with one more rule: the cut rating is the yarn’s, and the yarn survives washing; the coating does not survive heat. The live cut-glove care guide linked below has the full routine and when the rating is gone.
Leather drivers and leather palmHand wash cool with a mild soap, rinse, reshape and air-dry away from heat, then condition. MCR Safety’s leather statement: cowhide "stiffens when it gets wet"; pigskin "withstands moisture without getting stiff, dries soft and stays flexible, doesn’t lose its shape or function when laundered". So pigskin is the leather to buy for a glove that gets wet and washed. The leather cleaning guide linked below is the step-by-step.
Mechanics and impact glovesSynthetic-leather palm and spandex back: machine wash cold or warm on gentle, fasten the hook-and-loop closure first so it does not snag, air-dry. Thermoplastic rubber (TPR) impact bumpers and foam padding do not like a hot dryer.
Chemical gloves (PVC, nitrile, neoprene, latex)Rinse the outside under running water before taking them off, wash with soap and water, hang to dry open. Replace at the first sign of swelling, stickiness, cracking or a color change; the chemical has got into the material. A glove used with a chemical that permeates (solvents, acids) is not "cleaned" by washing, only by time, and the manufacturer’s chart decides whether it is reused at all.
Disposable nitrile, latex and vinylNot washed, not reused; single-use by design and by the Food Code where food is involved. The guide on when to change disposable gloves is linked below.
Winter and insulated glovesShell and lining wash as the shell type above; insulation (fleece, foam, Thinsulate, acrylic thermal knit) air-dries slowly and clumps in a hot dryer. Dry them open, cuff up.

The questions, one by one

Each answer is from the manufacturer’s own statements or the regulations named in the byline.

How often should you replace work gloves?

When the protective layer is gone, not on a calendar. For a coated knit that is a crack, hole or bare patch in the coating or a hole in the knit; for leather a cut, a hole, a palm worn thin or leather gone hard; for a cut-resistant glove a cut through the yarn; for a chemical glove any swelling, stickiness, crack or color change. OSHA’s 1910.132(e) says defective or damaged PPE shall not be used, and 1910.132(f) says the employee is trained in the glove’s "useful life". How long that takes is set by the work: a coated glove on rough block lasts days, on an assembly line months. The honest test is the inspection before each shift.

Are work gloves machine washable?

Cotton, jersey, string knit, coated knit, cut-resistant knit and mechanics gloves generally are, on a warm gentle cycle with a mild detergent and air-drying; MCR Safety prints laundering and machine-wash statements on its jersey and CutPro gloves. Leather is hand-washed; disposables are not washed; chemical gloves are rinsed and hung. "Site gloves" (the coated knit gloves a construction site hands out) are machine washable the same way, and a crew that washes them gets several more wears from each pair.

How do you clean gardening gloves?

By what they are made of. Cotton and jersey gardening gloves go through the machine warm and air-dry; nitrile- or latex-coated gardening gloves (the same construction as a coated work glove) wash warm on gentle and air-dry, with the dirt knocked off first; leather gardening gloves are brushed dry, wiped with a damp cloth and a little mild soap, reshaped and air-dried, then conditioned; rubber or PVC gardening gloves are rinsed and hung. Thorn-proof gloves with a leather palm follow the leather rule. Never a hot dryer for any of them.

Can I put work gloves in the dryer?

Cotton, jersey and string knits can take a dryer, with shrinkage. Coated, cut-resistant, mechanics, insulated and leather gloves should not: heat cracks coatings, melts the elastic and TPR, clumps insulation and hardens leather. Air-dry them open, cuff up, out of direct heat; a fan speeds it. Most "my gloves fell apart after I washed them" stories are a dryer story.

How do you get the smell out of work gloves, and how do you get rid of smelly hands from gloves?

The smell is bacteria living in sweat and oil in the glove. Wash the glove (warm, mild detergent, a cup of white vinegar in the wash helps on knits and coated gloves), dry it completely and fully open, and store it dry; a glove that is never fully dry never stops smelling. Rotating two pairs so each dries for a day is the single most effective fix. For the hands: wash with soap, dry well, and wear a cotton liner under a coated or rubber glove so the sweat is in the washable liner and not against the coating. A glove that still smells after two washes is at the end of its life.

How do you clean oil-soaked gloves?

A coated knit or cotton glove soaked in motor oil or hydraulic fluid: scrape off the excess, pre-treat the palm with a degreasing dish soap or a citrus hand cleaner, let it sit, then machine wash warm with detergent and air-dry; it may take two washes. Leather soaked in oil is largely a loss; the oil has gone into the hide and will soften and rot it. A chemical glove (PVC, nitrile) is the glove for oil in the first place, and it wipes clean. If the job is oil every day, the coated nitrile knit (nitrile resists oil, latex and polyurethane less so) is the glove, and a cotton liner under it catches the sweat.

How do you wash winter gloves?

By the shell: a leather winter glove is hand-washed cool and air-dried slowly, then conditioned; an insulated coated knit (Liberty Safety’s Arctic-Tuff acrylic thermal knits with a latex or nitrile palm) washes warm on gentle and air-dries open; a fleece-lined chore glove goes through the machine. The lining is the slow part: hang them cuff-up and give them a day. Do not dry insulation in a hot dryer; it clumps and loses its loft.

How do you wash mechanics gloves?

Close the hook-and-loop strap, turn them palm out, machine wash cold or warm on gentle with a mild detergent, air-dry. Synthetic leather tolerates this; real-leather palms (goatskin mechanics gloves) follow the leather rule. The TPR knuckle bumpers on an impact glove are glued and sewn on and do not like heat.

Is it necessary to wash your hands before putting on gloves?

For food handling the Food Code says yes: hands are washed before putting on single-use gloves (the food glove guide linked below has the section). For work gloves it is a care point rather than a rule: clean dry hands in a glove mean less sweat, oil and dirt inside it, a longer life and less smell. Mechanics in particular find a nitrile disposable under a mechanics glove keeps the glove clean and the hands clean at once.

Can suede gloves be washed, and what about the inside of leather gloves?

Suede (a split leather with a napped face) is brushed, not soaked; water marks it. Wipe the inside of a leather glove with a cloth wrung out in mild soapy water, turn the cuff back to dry it, and dust a cotton liner with talc if sweat is the problem. The leather cleaning guide linked below covers the inside, the smell and softening a glove that has dried hard.

Do gloves lose their rating when washed?

The cut rating belongs to the yarn and survives laundering; MCR Safety sells its CutPro knits for repeated machine washing. The coating is what wears: once it is cracked or thin the grip and the abrasion resistance are gone even though the cut rating is not. Chemical gloves can lose performance after exposure regardless of washing, which is why the manufacturer’s chart gives breakthrough times rather than a wash count. No manufacturer we carry publishes a number of washes; the inspection before each use is the test.

In plain words

  • Cotton, jersey, string knit, coated knit, cut-resistant and mechanics gloves machine wash warm on gentle; leather is hand-washed; chemical gloves are rinsed and hung; disposables are thrown away.
  • Air-dry everything except plain cotton. A hot dryer cracks coatings, clumps insulation and hardens leather.
  • Pigskin survives washing; cowhide stiffens when wet (MCR Safety’s leather statement). Condition leather after it dries.
  • Smell is bacteria in a damp glove: wash, dry completely, rotate two pairs, wear a cotton liner.
  • Replace a glove when the protective layer is gone: cracked or bare coating, holed knit, cut or hard leather, swollen or sticky rubber.
  • OSHA 1910.132(e): defective or damaged PPE shall not be used; 1910.132(f): employees are trained in care, useful life and disposal.
MCR Safety product pages and leather-type statements (mcrsafety.com, saved Nov 7 2026); 29 CFR 1910.132 Personal protective equipment, general requirements (eCFR, saved Nov 9 2026)

More questions people ask

How often should work gloves be replaced?

When they stop doing the job, not on a calendar. Armor Guys’ care page says to check before reuse "for cuts, coating wear, contamination, seam failure, loss of grip, and fit changes" and to remove gloves from service "when cuts, holes, coating breakdown, contamination, or loss of grip affects safety or control"; its FAQ adds that damaged gloves "should not be reused". Tracking how many pairs a task uses is how the cost-per-wear figure is worked out.

Can you wash cut-proof gloves?

Some, by the manufacturer’s instructions for that style. Armor Guys’ FAQ: "Laundering depends on the specific liner, coating, contamination, and SKU-level instructions", and its care page warns that laundering "can" change cut protection "if the glove is not designed or handled for laundering." Check the spec sheet before putting a dozen through a washer.

Answers from the sources named in the byline; Armor Guys figures from the manufacturer’s product pages, spec sheets, catalog C.009 and workbook C.010 read Nov 12 2026.

Questions people ask

How often should you replace work gloves?

When the protective layer is gone: cracked or bare coating, holed knit, cut or hardened leather, swollen chemical glove. Inspect before each shift; OSHA 1910.132(e) bars damaged PPE.

Are work gloves machine washable?

Cotton, coated knit, cut-resistant and mechanics gloves are, warm and gentle, air-dried. Leather is hand-washed; disposables are not washed.

How do you clean gardening gloves?

By material: cotton in the machine, coated knits warm and gentle, leather wiped and conditioned, rubber rinsed and hung. No hot dryer.

Can I put work gloves in the dryer?

Only plain cotton and jersey. Coated, cut-resistant, insulated, mechanics and leather gloves air-dry.

How do you get rid of smelly hands from gloves?

Wash the gloves, dry them completely, rotate two pairs, and wear a cotton liner so the sweat is in a washable layer.

How do you clean oil-soaked gloves?

Pre-treat with a degreasing soap, wash warm, air-dry; leather soaked in oil is usually finished. Use a nitrile chemical glove for daily oil.

Can cut-resistant gloves be washed?

Yes; the cut rating is in the yarn. Wash warm on gentle and air-dry; the coating is what wears out.

How do you wash mechanics gloves?

Strap closed, machine wash gentle, air-dry. Real-leather palms follow the leather rule.

Does pigskin or cowhide wash better?

Pigskin: MCR Safety prints that it dries soft and does not lose its shape when laundered; cowhide stiffens when wet.

Do gloves lose their rating when washed?

The cut rating survives; the coating and grip wear. No manufacturer we carry publishes a wash count.

How do you wash winter gloves?

By the shell; air-dry the insulation open and slowly, never in a hot dryer.

Is it necessary to wash your hands before putting on gloves?

Required by the Food Code for food handling; good practice for work gloves, since clean dry hands mean less sweat and smell.

The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.

Need gloves matched to a crew’s work?Call (925) 215-7337 or email us the task, the hazard and the sizes and we will quote by the dozen or the case with the manufacturer’s ratings listed. We sell nationwide.
Work glove selector

© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.

How to buyCard, purchase order or invoice terms; quotes on request; agencies and institutions welcome.
Live Service & SupportReal people who know the products, Monday to Friday 7:30am to 4pm Pacific. 925-215-7337
We DeliverWe ship nationwide. Parcel and LTL freight to job sites and businesses across the U.S.