Bayshore Safety & Industrial Supplies Guide
What is a Class 2 safety shirt, and what is a high-visibility jacket? Vest vs shirt vs jacket under ANSI/ISEA 107, Class 1 vs 2 vs 3, which colors are allowed for a hi-vis vest, what orange signifies, pink and black, and when each is worn
A Class 2 safety shirt is a T-shirt or long-sleeve shirt made of fluorescent background fabric with retroreflective bands, cut and taped so that it meets the ANSI/ISEA 107 Class 2 minimums on its own: at least 775 square inches of background and 201 square inches of reflective material, with 2 inch bands around the torso. It is a vest you cannot take off, which is the point: a crew in Class 2 shirts is in hi-vis all shift without a second layer, and in summer that is cooler than a vest over a shirt. A high-visibility jacket is the same idea in outerwear: a rain, work or insulated jacket whose shell is the fluorescent fabric and whose tape makes it Class 2 or, with sleeves taped, Class 3 (1,240 square inches of background, 310 of reflective). The standard rates garments, not styles, so a shirt, a jacket, a vest, a coverall, a pair of pants (Class E) or a rain suit is whatever class its area and tape earn. The background colors the standard allows are three, fluorescent yellow-green, fluorescent orange-red and fluorescent red; everything else, pink, blue, black, is enhanced visibility at most and not a class.
Liberty Safety HiVizGard C16730G Hi Vis Shirt, Class 3, Hi-Vis Green, PolyesterLiberty Safety prints ANSI/ISEA 107 Class 3, hi-vis green polyester, moisture-wicking, 2 inch reflective stripes, chest pocket; sold individuallyThe standard in two numbers. ANSI/ISEA 107 classes a garment by how much fluorescent background and how much retroreflective tape it carries, as our rule page states it: Class 1 at 217 square inches of background and 155 of reflective, Class 2 at 775 and 201, Class 3 at 1,240 and 310, with Class E for pants, shorts and gaiters that raise a Class 2 top to a Class 3 ensemble. Reflective bands are at least 2 inches wide for Class 2 and 3 (1 inch for Class 1), encircle the torso, and for Class 3 run on the arms or legs. The Type says the environment: Type O (off-road, Class 1 only), Type R (roadway and temporary traffic control, Class 2 or 3), Type P (public safety). The label inside the garment states the edition, Type, Class, size and care; Liberty Safety prints "ANSI/ISEA 107" and the class on each HiVizGard page.
Where it is required. On a public road: the MUTCD, which 29 CFR 1926.201(a) adopts for flaggers and 23 CFR 634 applies to every worker in the right of way of a federal-aid highway, requires Class 2 or 3. Off the road: OSHA’s general PPE rules (1926.95(a), 1910.132(a)) and its letters of interpretation, with the hazard assessment choosing the class; excavations under 1926.651(d). The does-OSHA-require-hi-vis guide linked below has the rule-by-rule answer.
Shirt, jacket, vest, pants: what each garment is and when it is worn
The garment statements are Liberty Safety’s; the class figures are the standard’s as the manufacturers print them.
The questions, one by one
Each answer uses the standard’s figures as the manufacturers print them and the rules named in the byline.
What is a Class 2 safety shirt?
A shirt that meets ANSI/ISEA 107 Class 2 by itself: fluorescent background of at least 775 square inches, at least 201 square inches of retroreflective tape in 2 inch bands around the torso, Type R. Liberty Safety’s C16620F is one ("Class 2, polyester, moisture wicking fabric, 2 inch wide silver reflective stripes"). It does the job of a Class 2 vest without the vest, and a Class E pant takes it to Class 3.
What is a high visibility jacket, and what color is a high vis jacket?
A jacket whose shell is fluorescent 107 background fabric with retroreflective bands, classed by its area and tape like any garment; the HiVizGard jackets are Class 3 because the sleeves are taped. The colors are the standard’s three: fluorescent yellow-green (what Liberty prints as "hi-vis green"), fluorescent orange-red and fluorescent red; the jackets in the band are hi-vis green with black lower panels ("black-bottom designs that help garments stay cleaner longer", as Liberty’s category page puts it), which the standard allows as long as the fluorescent area is still met.
What is a hi-vis shirt, and does OSHA require hi-vis shirts?
A hi-vis shirt is a fluorescent shirt with bands, Class 2 or 3 by its area and tape, or a plain fluorescent shirt with no bands and no class. OSHA does not name shirts; it requires high-visibility apparel of a class on roadways through the MUTCD and 1926.201, and elsewhere through the hazard assessment under 1926.95 and 1910.132. Whether the class is met by a shirt, a vest or a jacket is the employer’s choice.
Which colors are allowed for a hi-vis vest, and which do crews pick?
The standard allows three background colors and the manufacturers sell two: fluorescent yellow-green and fluorescent orange-red (fluorescent red is rare). Yellow-green is the most conspicuous in daylight to most eyes and is the default on construction sites; orange-red is the roadway and utility convention and the color that stands out against green foliage and against yellow-green crews. The orange-vs-yellow guide linked below weighs the two; the MUTCD accepts either. The reflective tape is silver (glass bead) or, on the Tech Series, white prismatic.
What are the key differences between Class 1 and Class 2 safety vests?
Area and use. Class 1: 217 square inches of background, 155 of tape, 1 inch bands, Type O only, for off-road work with no exposure to traffic over 25 mph and no moving equipment; Class 2: 775 and 201, 2 inch bands, Type R, the minimum for a roadway and for any site with vehicles or equipment. A Class 1 vest is a parking-lot and warehouse-aisle garment; a Class 2 vest is the jobsite one. Class 2 vs Class 3 is the next step, in the guide linked below.
Is class 3 hi-vis better than class 2?
Class 3 is more visible (1,240 square inches of background and 310 of tape, with the arms or legs taped, so the figure is recognizable as a person at a distance and at night); it is the class the MUTCD expects for night work and the highest-risk roadway positions, and the class a Class 2 top plus Class E pants makes. For a daylight site with slow traffic Class 2 is what the rules ask for, and a Class 3 shirt or jacket in summer heat is the trade. The hi-vis selector linked below filters by class.
What does wearing an orange safety vest signify, and what color is an engineer’s vest?
Nothing in the standard: orange is one of the allowed background colors and signifies the wearer is in hi-vis. By convention, orange is roadway, utility and rail (where orange is often mandated by the owner), and yellow-green is construction; some sites color-code trades, visitors or supervisors, and the why-wear-a-vest guide linked below covers that and the black vest question. "Engineer’s vest" in a search usually means the surveyor-style vest with pockets (Liberty C16010F, C16032FB) that engineers and inspectors wear, in either color.
Is pink a high-vis color, and can you wear black hi-vis?
Pink is not one of the three ANSI/ISEA 107 background colors, so a pink vest has no class however bright it is; it is enhanced-visibility apparel, fine where no rule requires a class and not a substitute where one does. Black appears on hi-vis garments only as trim and lower panels, as on the black-bottom vests and jackets, with the fluorescent area still meeting the class; an all-black "hi-vis" vest with tape is a Type O at most and usually no class. The black hi-vis guide linked below has the detail.
When should you wear a high visibility vest, and is it illegal to wear a high vis vest?
Whenever you are near moving vehicles or equipment, on a roadway (required by the MUTCD), in an excavation exposed to traffic (1926.651(d)), in a yard, dock, warehouse or plant where the hazard assessment finds a struck-by hazard, and whenever the site rules say so. It is not illegal to wear one anywhere; there is no law against a private citizen in a vest, and the question usually comes from impersonation concerns, which are about pretending to be an official, not about the vest.
What is the purpose of a hi-vis vest, and why wear hi-vis clothing at night when walking?
To be seen by a driver or an operator in time to stop: the fluorescent background is seen in daylight because it converts ultraviolet to visible light, and the retroreflective tape is seen at night because it sends a headlight’s beam back to the driver; the what-is-hi-vis guide linked below explains both. A pedestrian at night in dark clothing is visible to a driver at roughly a tenth of the distance of one in retroreflective material, which is the whole case for the tape.
Can I wash a high vis jacket, and how often should you replace hi-vis clothing?
Yes, by the care label: cold or warm wash, no bleach (it kills the fluorescence), no fabric softener on the tape, line or low tumble dry, and never a hot iron on the tape. A hi-vis garment is replaced when the fluorescent color has faded (compare it to a new one), when the tape is cracked, peeled or no longer flashes in a flashlight beam, or when it is torn or so soiled it no longer reads; the manufacturers’ guidance runs around six months for daily wear and the how-long-does-hi-vis-last guide linked below has the wash-count figures.
Who wears orange hi-vis jackets, and what constitutes hi-vis?
Roadway crews, utility crews, rail workers and anyone whose site specifies orange. What constitutes hi-vis under the standard: a garment with the fluorescent background and retroreflective tape areas of a class, labeled with its Type and Class by its manufacturer; anything short of that, however bright, is enhanced visibility.
In plain words
- The standard rates garments by area and tape, not by style: a shirt, jacket, vest, coverall or rain suit is Class 1, 2 or 3 by what it carries.
- Class 2: 775 square inches of background, 201 of tape, 2 inch bands round the torso. Class 3: 1,240 and 310, with arms or legs taped. Class E pants lift a Class 2 top to Class 3.
- A Class 2 shirt is a vest you cannot take off; a hi-vis jacket is the rain or winter answer because a vest covers a coat but not its arms.
- Three background colors: fluorescent yellow-green, orange-red, red. Pink and black carry no class.
- Roadways require Class 2 or 3 (MUTCD, 1926.201, 23 CFR 634); elsewhere the hazard assessment decides.
- Wash by the label, no bleach; replace when the color fades or the tape stops reflecting.
- Liberty Safety prints the class on every HiVizGard garment. We sell nationwide.
More questions people ask
What are high visibility jackets called?
By their cut: bomber jackets, parkas, soft shell jackets, 2-in-1 and 3-in-1 jackets (a shell with a zip-out liner), rain jackets, and hoodies and sweatshirts; ML Kishigo labels its Class 3 versions ANSI/ISEA 107 Type R Class 3. The jackets guide linked below goes through each.
Why would I wear a vest instead of a jacket?
Heat, cost and what is underneath. A Class 2 vest goes over any shirt or coat for a fraction of a jacket’s price and comes off at the truck; a Class 3 jacket is the choice when the work is at night, in weather or in traffic and the sleeves have to be hi-vis too. The vest-vs-jacket section above and the jackets guide linked below cover it.
What is the most breathable type of hi-vis shirt?
A mesh or birdseye-knit polyester: ML Kishigo prints "Ultra-Cool 100% polyester mesh" on its mesh vests and prints "Microfiber polyester material wicks away moisture" on its Class 2 and Class 3 T-shirts and "Cool Touch fabric with moisture wicking and anti-odor properties" with UPF 50+ on the Cool Touch shirts; the shirts guide linked below has the fabrics.
Answers from the sources named in the byline; ML Kishigo figures from the manufacturer’s product pages and spec sheets read Nov 12 2026.Questions people ask
What is a Class 2 safety shirt?
A fluorescent shirt with 2 inch reflective bands that meets ANSI/ISEA 107 Class 2 on its own: 775 square inches of background and 201 of tape.
What is a high visibility jacket?
A rain, work or insulated jacket in fluorescent fabric with bands, classed by its area and tape; the HiVizGard jackets are Class 3.
Which colors are allowed for a hi-vis vest?
The standard’s three: fluorescent yellow-green, orange-red and red. Yellow-green is the construction default, orange the roadway and utility convention.
What is the difference between Class 1 and Class 2?
Class 1 (217/155 square inches, Type O) is for off-road work with no traffic hazard; Class 2 (775/201, Type R) is the roadway and jobsite minimum.
Is Class 3 better than Class 2?
More visible, with taped arms or legs; required for night and high-speed roadway work. Class 2 plus Class E pants equals Class 3.
What does an orange safety vest signify?
Only that the wearer is in hi-vis; orange is the roadway, utility and rail convention, yellow-green the construction one.
Is pink a high-vis color?
Not under ANSI/ISEA 107; a pink vest has no class.
Can you wear black hi-vis?
Black is allowed as trim and lower panels; an all-black vest has no class.
Is it illegal to wear a high vis vest?
No. The concern people have is impersonating an official, which is about the pretense, not the vest.
When should you wear a high visibility vest?
Near moving vehicles or equipment, on roadways, in excavations exposed to traffic, and wherever the hazard assessment or site rules call for it.
Can I wash a high vis jacket?
Yes, by the label: no bleach, no softener, low heat; replace it when the color fades or the tape stops reflecting.
Does OSHA require hi-vis shirts?
OSHA requires hi-vis of a class on roadways and where the hazard assessment finds a struck-by hazard; shirt, vest or jacket is the employer’s choice.
Related guides
ANSI 107 Class 1, 2 and 3What the classes mean, and which one your job needsClass 2 vs Class 3 safety vestThe differenceWhat does Class E mean on hi-vis pants?Pants that raise a Class 2 top to Class 3Type R vs Type O vs Type PThe three high-visibility apparel typesAre yellow or orange safety vests better?What ANSI/ISEA 107 and the MUTCD sayWhy do workers wear hi-vis vests?Is it required, and can you wear black hi-visDoes OSHA require high-visibility clothing?The rules that call for itHow long does hi-vis clothing last?And when it should be replacedHi-vis for flaggers and roadway workWhat the MUTCD requiresWhat is enhanced visibility clothing?And why it is not Class 1, 2 or 3Hi-vis rain gear and cold-weather gearKeeping the class ratingWhat is hi-vis?How retroreflective material worksCan you get a safety vest custom printed with a logo?What ANSI/ISEA 107 allowsWhat are high-visibility jackets called?Bombers, parkas, soft shells, 2-in-1, rain jacketsWhat are hi-vis shirts made of?Microfiber polyester, Cool Touch, UPF 50+, black bottomThe ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.
© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.
