Bayshore Safety & Industrial Supplies Guide
What are hard hats called? Hard hat vs safety helmet vs bump cap and the trade names, the three classes and two types under ANSI/ISEA Z89.1, metal hard hats, forklifts, how much force a shell is tested to, the suspension clearance, and care
The standard calls it a protective helmet, OSHA’s rule calls it a protective helmet, and everyone who wears one calls it a hard hat; the industry’s newer word, safety helmet, means the climbing-style Type II helmet with a chin strap, and bump cap means the light cap that is not a hard hat at all. ANSI/ISEA Z89.1 sorts the real ones two ways: by Type (Type I, tested for a blow to the top of the head; Type II, tested for the top and the sides) and by electrical Class (Class G, general, tested at 2,200 volts; Class E, electrical, tested at 20,000 volts; Class C, conductive, no electrical rating, may be vented or metal). Those three classes are the "three classifications of hard hats", and Liberty Safety prints its DuraShell hats "Type I, Class G, E, C". The slang (brain bucket, skid lid, lid, tin hat, hard cap) is older than the standard; the first hard hats were steamed canvas and then aluminum, which is why metal hard hats still exist as Class C.
Liberty Safety DuraShell 1416RB Full Brim Hard Hat, 6-Point Ratchet, Type ILiberty Safety prints full brim, HDPE shell, 6-point ratchet suspension, ANSI/ISEA Z89.1 Type I Class G, E, C; sold individuallyThe names, sorted. Hard hat: the everyday word for any industrial protective helmet. Protective helmet: the word in 29 CFR 1910.135 ("each affected employee wears a protective helmet when working in areas where there is a potential for injury to the head from falling objects") and in Z89.1. Safety helmet: in current trade use, a Type II helmet with a chin strap and often a brimless climbing-style shell, as the safety-helmet guide linked below explains. Bump cap: a light shell for bumping into fixed objects, rated to ANSI/ISEA 100 or EN 812, not to Z89.1, and not the helmet 1910.135 names. Cap style and full brim: the two shapes, a short front brim or a brim all the way around. Hard hat parts: the shell, the suspension (crown straps, headband, nape strap, ratchet or pin-lock), the sweatband, the slots for accessories. Slang: brain bucket, skid lid, lid, tin hat, hard cap, construction helmet.
The force, in the manufacturer’s figures. MSA’s published test sheet for Z89.1-2014 states the Type I and Type II force-transmission test as a 3.6 kg (8 pound) mass striking the crown at 5.5 m/s, 54.5 joules ("equivalent: hammer falling from over 21 ft"), with a pass criterion of transmitted force "< 4450 N (1000 lb.)" and a sample average "< 3780 N (850 lb.)"; the apex penetration test a 1.0 kg pointed striker at 7.0 m/s, 30.6 joules ("hammer falling from nearly 12 ft"), with the pass criterion that the penetrator "shall not make contact with top of test headform"; Type II adds an off-center impact at 5.0 m/s and an off-center penetration at 3.6 m/s. That is what "how much force can a hard hat withstand" means in the standard: the shell and suspension together must keep the force reaching the head under 1,000 pounds from that blow.
Type, class and the rest of the label
The definitions are as the manufacturers and Cal/OSHA 3381 state them; the figures are MSA’s published test sheet.
The questions, one by one
Each answer uses the manufacturers’ statements, MSA’s test sheet and the regulations named in the byline.
What are hard hats called?
Protective helmets in the rule and the standard; hard hats on every site; safety helmets when they are the Type II climbing-style kind; bump caps when they are the light non-rated kind. By shape, cap style and full brim; by trade, a lineman’s hat (Class E), a welder’s hat (a hard hat with a welding helmet adapter), a miner’s cap (with a lamp bracket), an arborist helmet (a Type II helmet with a chin strap for climbing, usually vented, Class C). Slang: brain bucket, skid lid, lid, tin hat, hard cap. In the catalog the name is "hard hat" plus the type and class, which is what to read.
What is a safety helmet called, and how do you explain a helmet?
A safety helmet is a hard hat built like a climbing helmet: a shell, a suspension or foam liner, and a chin strap, tested to Z89.1 Type II for side impact as well as top. Explained in one sentence: a helmet is a hard shell held off the head by a suspension, so that a blow to the shell is spread across it and absorbed by the straps stretching into the gap, instead of landing on one spot of the skull. The parts are the shell, the suspension (crown straps, headband, nape strap, ratchet), the sweatband and the chin strap where fitted; the suspension guide linked below shows them.
What are the three classifications of hard hats?
Class G (general, 2,200 volt test), Class E (electrical, 20,000 volt test) and Class C (conductive, no electrical test), as OSHA’s PPE booklet gives them and the manufacturers print them. The old names were A, B and C; the Z89.1 1997 edition renamed A to G and B to E. The two Types (I and II) are the impact classification, a separate axis: a hat is Type I or II and Class G, E or C, and Liberty Safety’s DuraShell hats are Type I in all three classes.
What does "hard hat" mean in slang?
Outside the trade "hard hat" means the worker, not the hat: a hardhat is a construction worker, as in the 1970 "hard hat" demonstrations, and the phrase carries the blue-collar sense. On a site the slang runs the other way, toward the object: brain bucket, lid, skid lid. "Hard hat area" on a sign means a place where 1910.135 or 1926.100 requires the helmet.
Are there metal hard hats?
Yes. Aluminum hard hats were the standard from the 1930s to the 1960s and are still made for forestry, oil and gas and heat (they do not soften in the sun); under Z89.1 they can only be Class C, since metal conducts, and OSHA’s 1910.135(a)(2) bars them near exposed electrical conductors. Fiberglass hats fill the same heat niche with a Class G or E rating; the materials guide linked below compares HDPE, ABS, polycarbonate, fiberglass and metal. None of the DuraShell hats is metal.
Are hard hats required on forklifts, and should forklift drivers wear hard hats?
OSHA’s powered industrial truck rule, 1910.178, has no hard hat paragraph; the head rule, 1910.135(a)(1), applies wherever "there is a potential for injury to the head from falling objects", and a forklift aisle under loaded racking is such a place in most warehouses, which is why the employer’s hazard assessment under 1910.132(d) usually puts a hard hat on the driver and the pickers alike. A forklift’s overhead guard protects against a falling load from the forks, not from the rack beside it. The hazard assessment decides, and the answer on most sites is yes.
How much force can a hard hat withstand?
The standard sets a test, not a maximum: MSA’s published Z89.1-2014 sheet gives the force-transmission test as 3.6 kg at 5.5 m/s (54.5 joules, "equivalent: hammer falling from over 21 ft.") with transmitted force under 4,450 N (1,000 pounds) on any sample and under 3,780 N (850 pounds) on average, and the penetration test as a 1.0 kg point at 7.0 m/s (30.6 joules) that must not touch the headform. A hat that passes has kept a 40-foot-pound blow to the crown down to under 1,000 pounds at the head. It is tested once; after a real blow of that order the hat is replaced, as the inspection and expiry guides linked below explain.
What is the measurement that a hard hat’s suspension system should maintain?
The clearance between the crown of the shell and the top of the head: the suspension holds the shell off the skull by about a finger’s width, and the manufacturer’s instructions set the exact gap for each model. That gap is the protection, because the crown straps stretch into it when the shell is struck; a radio, gloves or a ball cap stuffed into the crown, a cut strap or an unseated key removes it. The suspension guide linked below walks through seating the keys and checking the gap.
Which hard hat sits low on the head, and which hard hat protects against electrical hazards?
Hats with a suspension whose crown straps clip into the headband at a lower setting sit lower while keeping the clearance; the how-to-wear guide linked below explains the adjustment and why the shell is never dropped by removing straps. For electrical hazards: Class E (20,000 volt test) for work near high-voltage conductors, Class G (2,200 volts) for low voltage, never Class C, and never a vented shell, which turns a Class G or E hat into Class C as the vented-hat guide linked below explains. Every DuraShell cap and full brim in the band is printed Class G, E and C.
What actions do you need to take to properly care for your hard hat?
Inspect it before each shift (shell for cracks, dents, gouges, chalking and loss of gloss; suspension for cut or frayed straps, a slipping ratchet, unseated keys); wash the shell and suspension in warm water and mild soap, rinse and air-dry, no solvents, no dishwasher; store it out of the sun and away from heat (the back window of a truck is the fastest way to age a shell); do not paint it or add stickers except as the manufacturer allows (paint solvents and metallic labels are the issues; the stickers guide linked below has the Z89.1 appendix wording); replace the suspension on the manufacturer’s schedule and the hat after any significant blow or at the service life the manufacturer prints. OSHA’s 1910.132(e) bars damaged PPE outright.
What kind of helmet do electricians wear, and what is an arborist helmet?
Electricians wear a Class E hard hat (20,000 volt test), unvented, cap style or full brim, often in a conventional Type I; linemen and tree crews near lines wear the same class, and crews that climb wear a Type II helmet with a chin strap in Class E. An arborist helmet is a Type II climbing-style helmet with a chin strap and usually vents, which makes it Class C and keeps it away from lines; the EN 397 vs EN 12492 vs Z89.1 guide linked below explains why a climbing helmet is not automatically a Type II.
How much do construction helmets cost?
A Type I cap-style HDPE hard hat with a ratchet suspension runs about $10 to $13 on our site today (the DuraShell 1404 and 1406 series), a full brim about $11 to $12 (the 1416 series), and a bump cap about $6 to $12; Type II safety helmets with chin straps from the other lines we carry run several times that, and the brands guide linked below has the model names. The live price is on each row below.
In plain words
- The rule says protective helmet; the site says hard hat; safety helmet means a Type II helmet with a chin strap; a bump cap is not a hard hat.
- Two Types: I (top of head) and II (top and sides). Three Classes: G (2,200 V), E (20,000 V), C (no electrical rating, may be vented or metal).
- MSA’s Z89.1 test sheet: an 8 pound mass at 5.5 m/s, transmitted force under 1,000 pounds; a 1 kg point at 7 m/s must not reach the head.
- Metal hard hats exist and are Class C only. Forklift drivers wear one where a falling object hazard exists, which is most warehouses.
- The suspension keeps the shell about a finger’s width off the head; the gap is the protection.
- Care: inspect each shift, wash with mild soap, keep out of the sun, no solvents or paint, replace after a blow or at the printed service life.
- Every DuraShell hard hat is printed Type I, Class G, E, C; cap style and full brim. We sell nationwide.
Questions people ask
What are hard hats called?
Protective helmets in OSHA’s rule and the standard; hard hats on site; safety helmets for the Type II chin-strap kind; bump caps for the light non-rated kind; slang brain bucket, lid, skid lid.
What are the three classifications of hard hats?
Class G (2,200 volt test), Class E (20,000 volts) and Class C (conductive, no electrical test); Types I and II are the separate impact classification.
What is a safety helmet called?
A Type II hard hat with a chin strap, built like a climbing helmet.
Are there metal hard hats?
Yes, aluminum hats for forestry, oil and gas and heat; they are Class C only and barred near exposed conductors.
Are hard hats required on forklifts?
Not by the forklift rule, but 1910.135 applies wherever falling objects are a hazard, which is most warehouses; the hazard assessment decides.
How much force can a hard hat withstand?
MSA’s Z89.1 test sheet: a 3.6 kg mass at 5.5 m/s (54.5 joules) with transmitted force under 4,450 N (1,000 pounds); a 1 kg point at 7 m/s must not touch the headform.
What clearance should the suspension keep?
About a finger’s width between shell and head, set by the manufacturer’s instructions; the gap absorbs the blow.
Which hard hat protects against electrical hazards?
Class E for high voltage, Class G for low voltage, unvented; never Class C.
How do you care for a hard hat?
Inspect each shift, wash with mild soap and water, keep out of sun and heat, no solvents or paint, replace after a blow or at the printed service life.
What kind of helmet do electricians wear?
A Class E hard hat, unvented; climbing crews a Type II Class E helmet with a chin strap.
What is an arborist helmet?
A Type II climbing-style helmet with a chin strap, usually vented (Class C).
How much do construction helmets cost?
About $10 to $13 for a Type I cap or full brim on our site today; Type II safety helmets several times that.
What does hard hat mean in slang?
Outside the trade, the construction worker; on site, the hat itself is the brain bucket or lid.
Related guides
Safety helmet vs hard hatWhat the chin strap and Type II changeBump cap vs hard hatWhen a bump cap is allowedType I vs Type II hard hatsWhat the types meanClass G, Class E and Class C hard hatsThe electrical ratingsWhat are hard hats made of?HDPE, polycarbonate, fiberglass and ABSVented hard hatsWhat the ventilation does to the electrical classHow to assemble a hard hat suspensionStep by stepHow to wear a hard hat correctlyAnd can you wear it backwardsHard hat inspectionWhat to check and how oftenDo hard hats expire?Service life, the date stamp, and when to replace oneDoes OSHA allow stickers on hard hats?What the manufacturer statesWhich companies make hard hats and safety helmets?The manufacturers and model namesWhat are hard hats designed to protect you from?Top impact, penetration and electrical contactIs it a legal requirement to wear a hard hat?Who decides, who pays, what OSHA citesThe ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.
© 2026 Bayshore Safety & Industrial Supplies, Inc. All rights reserved. This guide may not be copied or republished without written permission.
