Fall Protection for Ironworkers and Steel Erection
Fall Protection for Ironworkers and Steel Erection: the OSHA and Cal/OSHA rule paragraphs condensed and linked, and the Safewaze and FallTech products whose own data names steel erection. We sell nationwide; ships in 1–2 business days; most orders arrive in 3–7 business days.
What the federal rule says
Each entry is condensed from the paragraph cited; the paragraph itself is the rule and the link opens it.
29 CFR 1926.760(a)(1): Steel erection: except as provided for connectors and controlled decking zones, each employee engaged in a steel erection activity on a walking/working surface with an unprotected side or edge more than 15 feet above a lower level must be protected by guardrail systems, safety net systems, personal fall arrest systems, positioning device systems or fall restraint systems.
29 CFR 1926.760(b): Connectors: each connector must be protected from falls of more than two stories or 30 feet above a lower level, whichever is less; must have completed connector training; and at heights over 15 and up to 30 feet must be provided with a personal fall arrest system, positioning device system or fall restraint system and wear the equipment necessary to tie off, or be provided with other means of protection from fall hazards.
29 CFR 1926.760(c): Controlled decking zones: a CDZ may be established in an area of the structure over 15 and up to 30 feet above a lower level where metal decking is initially being installed; access is limited to employees engaged in leading-edge work, and the zone is limited to 90 feet wide and 90 feet deep from any leading edge.
29 CFR 1926.760(d): Fall protection systems used in steel erection must meet the criteria of 1926.502; perimeter safety cables must meet 1926.502(b) criteria; fall protection provided by the steel erector may remain in the area where steel erection is completed only if the controlling contractor directs it and inspects and accepts it.
29 CFR 1926.760(e): Custody of fall protection: fall protection provided by the steel erector shall remain in the area where steel erection activity has been completed, to be used by other trades, only if the controlling contractor or its authorized representative has directed the steel erector to leave it in place, and has inspected and accepted control and responsibility for it.
29 CFR 1926.502(d)(15): Anchorages used for attachment of personal fall arrest equipment must be independent of any anchorage used to support or suspend platforms and capable of supporting at least 5,000 pounds per employee attached, or be designed, installed and used under the supervision of a qualified person as part of a complete system that maintains a safety factor of at least two.
29 CFR 1926.502(d)(16): A personal fall arrest system must limit the maximum arresting force on an employee to 1,800 pounds when used with a body harness, be rigged so the employee can neither free fall more than 6 feet nor contact any lower level, bring the employee to a complete stop and limit the deceleration distance to 3.5 feet, and have sufficient strength to withstand twice the potential impact energy of a 6-foot free fall.
Source: 29 CFR, Occupational Safety and Health Standards, as published by OSHA (ecfr.gov), read Nov 6 2026.
California (Cal/OSHA)
Each entry is condensed from the paragraph cited; the paragraph itself is the rule and the link opens it.
Title 8 §1710(m)(1): Structural steel erection, connecting: when connecting beams or other structural members where the fall distance is greater than two stories or 30 feet, whichever is less, iron workers shall be provided with and use a personal fall protection system tied off to columns, pendant lines secured at the tops of columns, catenary lines or other secure anchorage points; at heights over 15 and up to 30 feet, connectors shall be provided with a personal fall arrest, positioning device or fall restraint system and wear the equipment necessary to tie off, or be provided with other means of protection.
Title 8 §1710(m)(2): During steel erection work other than connecting, fall protection is required where the fall distance is greater than 15 feet (Cal/OSHA Pocket Guide for the Construction Industry summary of §1710(m)).
Title 8 §1670(a): Approved personal fall arrest, personal fall restraint or positioning systems shall be worn by employees whose work exposes them to falling in excess of 7 1/2 feet from the perimeter of a structure, unprotected sides and edges, leading edges, through shaftways and openings, sloped roof surfaces steeper than 7:12, or other sloped surfaces steeper than 40 degrees not otherwise adequately protected. Body belts shall not be used as part of a personal fall arrest system (effective January 1, 1998).
Source: California Code of Regulations, Title 8, as published by Cal/OSHA (dir.ca.gov), read Nov 6 2026.
Safewaze and FallTech products whose own description names steel erection
Each section lists the styles whose manufacturer title, page, category or document names the structure or the use; the ratings are the manufacturer's. Sizes and lengths are chosen on the style page. The series pages carry every part number, the standards written out and the documents. Safewaze first, then FallTech; the line above each FallTech table says which FallTech page or document put it here.
Safewaze steel anchors: beam clamps, trolleys and sliders
Safewaze names the flange range in each title (beam walkers, sliding beam anchors, beam trolleys and vertical or stationary beam anchors).
Every part number in the series, with sizes and lengths: Safewaze Steel Anchors.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze cross arm straps
| Part number | Item | Version | Price | ||
|---|---|---|---|---|---|
 | FS-EX400 | Safewaze FS-EX400 Anchor Straps, Ratchet Cross Arm | 2 versions: 15 ft, 30 ft | $133.00 | Choose on the page |
 | FS810 | Safewaze FS810 Anchor Straps, Reinforced Cross Arm | 6 versions: 3 ft, 6 ft, 8 ft, 10 ft, 15 ft, 20 ft | $34.99 | Choose on the page |
 | FS811 | Safewaze FS811 Anchor Straps, Cross Arm | 6 versions: 3 ft, 4 ft, 6 ft, 10 ft, 15 ft, 20 ft | $27.99 | Choose on the page |
 | FS812 | Safewaze FS812 Anchor Straps, Adjustable Cross Arm | $43.99 | ||
 | FS815 | Safewaze FS815 Anchor Straps, Scaffold Anchor | $30.99 | ||
 | FS830-C | Safewaze FS830-C Cable Anchors, Cable Choker Anchor | 5 versions: 3 ft, 4 ft, 6 ft, 8 ft, 10 ft | $51.49 | Choose on the page |
 | FS88811-HW | Safewaze FS88811-HW Anchor Straps, 6 ft Heavy Duty Cross Arm | $37.99 |
Every part number in the series, with sizes and lengths: Safewaze Strap Anchors.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze leading-edge SRLs and lanyards
Safewaze titles these for leading edges: Class 2 SRLs under Z359.14-2021 and lanyards it describes as leading-edge rated.
Every part number in the series, with sizes and lengths: Safewaze Latitude Edge SRLs · Safewaze Leading Edge Lanyards.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze dual-leg lanyards for 100 percent tie-off
Every part number in the series, with sizes and lengths: Safewaze PRO Lanyards · Safewaze PRO Stretch Lanyards.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze harnesses with side D-rings for positioning
Every part number in the series, with sizes and lengths: Safewaze PRO Harnesses · Safewaze PRO+ Slate Harnesses · Safewaze PRO+ Harnesses.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze positioning assemblies
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
Safewaze tool tethers
Tool tethers Safewaze rates under ANSI/ISEA 121 for dropped-object prevention; the load limit is on each page.
Every part number in the series, with sizes and lengths: Safewaze Tool Tethers.
Source: Safewaze product pages and technical data sheets (safewaze.com, fetched Nov 6 2026); the 2025 Safewaze file; the products listed are the Safewaze styles whose own description names the use or the structure, not a selection by Bayshore Safety.
FallTech steel anchors: beam clamps, sliders and bolt-on anchors
Why these are here: FallTech Steel anchorages category (falltech.com/fall-protection-products/anchorages/steel/), each anchor's own description naming the beam or steel member.
24 FallTech styles qualify; the first 16 are listed and every part number is on the series pages: FallTech Steel Anchorage.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech FT-Iron harnesses
Why these are here: FT-Iron harnesses, which FallTech describes as "the iron worker's must-have harness" on its Steel Erection and Metal Decking industry pages.
Every part number in the series: FallTech FT-Iron.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech leading edge SRLs
Why these are here: FallTech Leading Edge SRLs category (falltech.com/fall-protection-products/srls/leading-edge-srls/); Class 2 under ANSI/ASSP Z359.14-2021 on each page; the FT-R and FT-X EdgeCore series are featured on the Steel Erection industry page.
62 FallTech styles qualify; the first 16 are listed and every part number is on the series pages: FallTech FT-R · FallTech DuraTech · FallTech CTX Cable Leading Edge · FallTech Contractor · FallTech FT-X Cable Leading Edge · FallTech FT-X EdgeCore Arc Flash Leading Edge · FallTech FT-X EdgeCore Leading Edge.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech leading edge lanyards
Why these are here: FallTech Leading Edge lanyards category and the Leading Edge Lanyard sell sheet ("foot-level tie-off for leading edge applications").
Every part number in the series: FallTech Leading Edge Lanyards.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech rebar and work positioning lanyards
Why these are here: FallTech Rebar Positioning lanyards; the positioning lanyard manual MPOL01 names "concrete form work and steel erection" as the work positioning use.
| Part number | Item | Version | Price | ||
|---|---|---|---|---|---|
 | 8048WS | FallTech 8048WS Positioning Lanyards, EdgeCore Web Spreader | $135.20 | ||
 | 8048WSL | FallTech 8048WSL Positioning Lanyards, EdgeCore Web Spreader | $135.20 | ||
 | 8250 | FallTech 8250 Positioning Lanyards, 23 in Premium Rebar, Chain | 3 versions: Chain and Steel Swivel Rebar Hook, Jacketed Web and Steel Swivel Rebar Hook, GR | $95.60 | Choose on the page |
 | 825010LK | FallTech 825010LK Positioning Lanyards, 19 in Premium Rebar | $134.40 | ||
 | 825012W | FallTech 825012W Positioning Lanyards, 19 in Rebar | $104.40 | ||
 | 82506L | FallTech 82506L Positioning Lanyards, 17 in Premium Rebar | $133.20 | ||
 | 8250A | FallTech 8250A Positioning Lanyards, 24 in Premium Rebar | $165.20 | ||
 | 8250LT | FallTech 8250LT Positioning Lanyards, 21 in Standard-duty Rebar | $108.00 | ||
 | 8250LT10LK | FallTech 8250LT10LK Positioning Lanyards, 17 in Standard-duty Rebar | $104.40 | ||
 | 8250LTW | FallTech 8250LTW Positioning Lanyards, 24 in Standard-duty Rebar, Jacketed Web | 2 versions: Jacketed Web and Steel non-Swivel Rebar Hook, Jacketed Web and Aluminum non-Swiv | $85.20 | Choose on the page |
Every part number in the series: FallTech Rebar Positioning.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech dual-leg lanyards for 100 percent tie-off
Why these are here: dual-leg energy absorbing lanyards; the FallTech lanyard manual MSAL01 states "All FallTech dual-leg SAL's are approved for 100% Tie-Off applications".
30 FallTech styles qualify; the first 16 are listed and every part number is on the series pages: FallTech ElasTech · FallTech WeldTech · FallTech Arc Flash Lanyards · FallTech Heavyweight · FallTech Ironman · FallTech ViewPack · FallTech FT Basic.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
FallTech SteelGrip horizontal lifelines
Why these are here: SteelGrip cable horizontal lifeline systems, featured on the FallTech Metal Decking industry page.
Every part number in the series: FallTech SteelGrip Cable HLL.
Source: FallTech product pages (falltech.com, fetched Nov 8 2026), FallTech category and industry pages, instruction manuals and brochures as cited above each table; the products listed are the FallTech styles that FallTech's own pages or documents place in this work, not a selection by Bayshore Safety.
Manufacturer sizing and fall clearance documents
Safewaze: Harness Fitting and Sizing (PDF) · Fall Clearance Chart (PDF). FallTech: Harness Sizing Chart, men 2026 (PDF) · Harness Sizing Chart, women 2026 (PDF) · Calculating Fall Clearance poster (PDF) · SRL quick guide (PDF). Each manufacturer's document applies to its own products; the figures on a style page come from that style's data sheet.
Guides: OSHA 1926 Subpart M explained · leading-edge SRLs · anchor points and the 5,000 lb rule · arrest vs restraint vs positioning · carabiners and snap hooks · every fall protection item by type and standard.
Fall Protection for Ironworkers and Steel Erection questions
What is the difference between a leading edge SRL and a standard SRL? ANSI/ASSP Z359.14-2021 sorts self-retracting devices into Class 1, rated for anchorage at or above the dorsal D-ring, and Class 2, tested for anchorage below the D-ring and for the lifeline running over an edge. Safewaze lists the class on each SRL page (Latitude Edge is its Class 2 series); FallTech files its Class 2 devices under Leading Edge SRLs (FT-R, FT-R+, FT-X Cable, FT-X EdgeCore, CTX, Contractor and DuraTech cable SRLs) and prints the class on each page. The arrest distances for each class are in the manufacturer's data sheet.
At what height is 100% tie off mandatory? No OSHA paragraph uses the phrase; "100 percent tie-off" is the practice of staying connected while moving, done with a dual-leg lanyard or two devices. The steel erection trigger is 15 feet (29 CFR 1926.760(a)(1)), connectors are covered between 15 and 30 feet under 1926.760(b), and Cal/OSHA §1710(m) sets the same 15 and 30 foot figures. FallTech's lanyard manual states that all FallTech dual-leg energy absorbing lanyards are approved for 100 percent tie-off applications; Safewaze titles its dual-leg lanyards for the same use.
Can you use a beam clamp for fall protection? A beam clamp sold as an anchorage connector can be, when it meets 1926.502(d)(15): rated for 5,000 pounds per employee attached or used under a qualified person in a system with a safety factor of two. Safewaze and FallTech each title their beam anchors by the flange range they fit and print the rated strength and the standard named (ANSI/ASSP Z359.18 where the data sheet names it) on the page; a rigging clamp made for lifting is not that product.
What does "leading edge" mean? 29 CFR 1926.500(b) defines it: the edge of a floor, roof, or formwork for a floor or other walking/working surface (such as the deck) which changes location as additional floor, roof, decking, or formwork sections are placed, formed, or constructed; a leading edge is considered an unprotected side and edge during periods when it is not actively and continuously under construction.
What are the OSHA safety requirements for leading edges? 29 CFR 1926.501(b)(2): each employee constructing a leading edge 6 feet or more above a lower level must be protected by guardrail systems, safety net systems or personal fall arrest systems, with a fall protection plan under 1926.502(k) only where the employer demonstrates those are infeasible or create a greater hazard. In steel erection the figures are 1926.760's: 15 feet generally, with the connector and controlled decking zone provisions between 15 and 30 feet.
What equipment must connectors wear when working at heights over 15 and up to 30 feet? 29 CFR 1926.760(b)(3): a connector working at heights over 15 and up to 30 feet above a lower level must be provided with a personal fall arrest system, positioning device system or fall restraint system and wear the equipment necessary to be able to be tied off, or be provided with other means of protection from fall hazards; above two stories or 30 feet, whichever is less, the connector must be protected ((b)(1)). Cal/OSHA §1710(m)(1) uses the same figures.
The ratings, test results and standards shown here are the manufacturers' published values, reproduced as published. Nothing on this page is a recommendation by Bayshore Safety that any product is suitable for a particular task, hazard or workplace. Selecting safety products and protective equipment is the responsibility of the end user and the employer, based on their own hazard assessment and the regulations that apply to their work. Confirm every value on the manufacturer's own documentation before use.